mirror of
https://gitlab.torproject.org/tpo/core/tor.git
synced 2024-12-03 00:53:32 +01:00
93 lines
3.7 KiB
Plaintext
93 lines
3.7 KiB
Plaintext
Filename: 151-path-selection-improvements.txt
|
|
Title: Improving Tor Path Selection
|
|
Version:
|
|
Last-Modified:
|
|
Author: Fallon Chen, Mike Perry
|
|
Created: 5-Jul-2008
|
|
Status: Draft
|
|
|
|
Overview
|
|
|
|
The performance of paths selected can be improved by adjusting the
|
|
CircuitBuildTimeout and avoiding failing guard nodes. This proposal
|
|
describes a method of tracking buildtime statistics, and using those
|
|
statistics to adjust the CircuitBuildTimeout and the number of guards.
|
|
|
|
Motivation
|
|
|
|
Tor's performance can be improved by excluding those circuits that
|
|
have long buildtimes (and by extension, high latency). For those Tor
|
|
users who require better performance and have lower requirements for
|
|
anonymity, this would be a very useful option to have.
|
|
|
|
Implementation
|
|
|
|
Learning the CircuitBuildTimeout
|
|
|
|
Based on studies of build times, we found that the distribution of
|
|
circuit buildtimes appears to be a Pareto distribution. The number
|
|
of circuits to observe (ncircuits_to_cutoff) before changing the
|
|
CircuitBuildTimeout will be tunable. From out measurements,
|
|
ncircuits_to_cuttoff appears to be on the order of 100.
|
|
|
|
In addition, the total number of circuits gathered
|
|
(ncircuits_to_observe) will also be tunable. It is likely that
|
|
ncircuits_to_observe will be somewhere on the order of 1000. The values
|
|
can be represented compactly in Tor in milliseconds as a circular array
|
|
of 16 bit integers. More compact long-term storage representations can
|
|
be implemented by simply storing a histogram with 50 millisecond buckets
|
|
when writing out the statistics to disk.
|
|
|
|
Calculating the preferred CircuitBuildTimeout
|
|
|
|
Circuits that have longer buildtimes than some x% of the estimated
|
|
CDF of the Pareto distribution will be excluded. x will be tunable
|
|
as well.
|
|
|
|
Circuit timeouts
|
|
|
|
In the event of a timeout, backoff values should include the 100-x%
|
|
of expected CDF of timeouts. Also, in the event of network failure,
|
|
the observation mechanism should stop collecting timeout data.
|
|
|
|
Dropping Failed Guards
|
|
|
|
In addition, we have noticed that some entry guards are much more
|
|
failure prone than others. In particular, the circuit failure rates for
|
|
the fastest entry guards was approximately 20-25%, where as slower
|
|
guards exhibit failure rates as high as 45-50%. In [1], it was
|
|
demonstrated that failing guard nodes can deliberately bias path
|
|
selection to improve their success at capturing traffic. For both these
|
|
reasons, failing guards should be avoided.
|
|
|
|
We propose increasing the number of entry guards to five, and gathering
|
|
circuit failure statistics on each entry guard. Any guards that exceed
|
|
the average failure rate of all guards by 10% after we have
|
|
gathered ncircuits_to_observe circuits will be replaced.
|
|
|
|
|
|
Issues
|
|
|
|
Impact on anonymity
|
|
|
|
Since this follows a Pareto distribution, large reductions on the
|
|
timeout can be achieved without cutting off a great number of the
|
|
total paths. However, hard statistics on which cutoff percentage
|
|
gives optimal performance have not yet been gathered.
|
|
|
|
Guard Turnover
|
|
|
|
We contend that the risk from failing guards biasing path selection
|
|
outweighs the risk of exposure to larger portions of the network
|
|
for the first hop. Furthermore, from our observations, it appears
|
|
that circuit failure is strongly correlated to node load. Allowing
|
|
clients to migrate away from failing guards should naturally
|
|
rebalance the network, and eventually clients should converge on
|
|
a stable set of reliable guards. It is also likely that once clients
|
|
begin to migrate away from failing guards, their load should go
|
|
down, causing their failure rates to drop as well.
|
|
|
|
|
|
[1] http://www.crhc.uiuc.edu/~nikita/papers/relmix-ccs07.pdf
|
|
|