Don't touch the string representation in routerinfo_t->address.
Also, set or clear the routerinfo_t->ipv6_preferred flag based on the
address family of the bridge.
Comments below focus on changes, see diff for added code.
New type tor_addr_port_t holding an IP address and a TCP/UDP port.
New flag in routerinfo_t, ipv6_preferred. This should go in the
node_t instead but not now.
Replace node_get_addr() with
- node_get_prim_addr() for primary address, i.e. IPv4 for now
- node_get_pref_addr() for preferred address, IPv4 or IPv6.
Rename node_get_addr_ipv4h() node_get_prim_addr_ipv4h() for
consistency. The primary address will not allways be an IPv4 address.
Same for node_get_orport() -> node_get_prim_orport().
Rewrite node_is_a_configured_bridge() to take all OR ports into account.
Extend argument list to extend_info_from_node and
extend_info_from_router with a flag indicating if we want to use the
routers primary address or the preferred address. Use the preferred
address in as few situtations as possible for allowing clients to
connect to bridges over IPv6.
we don't need to check whether we don't have enough guards right after
concluding that we do have enough.
slight efficiency fix suggested by an anonymous fellow on irc.
With managed proxies you would always get the error message:
"You have a Bridge line using the X pluggable transport, but there
doesn't seem to be a corresponding ClientTransportPlugin line."
because the check happened directly after parse_client_transport_line()
when managed proxies were not fully configured and their transports
were not registered.
The fix is to move the validation to run_scheduled_events() and make
sure that all managed proxies are configured first.
* Create mark/sweep functions for transports.
* Create a transport_resolve_conflicts() function that tries to
resolve conflicts when registering transports.
For printf, %f and %lf are synonymous, since floats are promoted to
doubles when passed as varargs. It's only for scanf that we need to
say "%lf" for doubles and "%f" for floats.
Apparenly, some older compilers think it's naughty to say %lf and like
to spew warnings about it.
Found by grarpamp.
Instead, use compare_tor_addr_to_node_policy everywhere.
One advantage of this is that compare_tor_addr_to_node_policy can
better distinguish 0.0.0.0 from "unknown", which caused a nasty bug
with microdesc users.
* Add some utility transport functions in circuitbuild.[ch] so that we
can use them from pt.c.
* Make the accounting system consider traffic coming from proxies.
* Make sure that we only fetch bridge descriptors when all the
transports are configured.
Rationale: right now there seems to be no way for our bootstrap
status to dip under 100% once it has reached 100%. Thus, recording
broken connections after that point is useless, and wastes memory.
If at some point in the future we allow our bootstrap level to go
backwards, then we should change this rule so that we disable
recording broken connection states _as long as_ the bootstrap status
is 100%.
It's very easy for nodelist_add_node_family(sl,node) to accidentally
add 'node', and kind of hard to make sure that it omits it. Instead
of taking pains to leave 'node' out, let's instead make sure that we
always include it.
I also rename the function to nodelist_add_node_and_family, and
audit its users so that they don't add the node itself any longer,
since the function will take care of that for them.
Resolves bug 2616, which was not actually a bug.
Previously, we'd just take all the nodes in EntryNodes, see which
ones were already in the guard list, and add the ones that weren't.
There were some problems there, though:
* We'd add _every_ entry in EntryNodes, and add them in the order
they appeared in the routerlist. This wasn't a problem
until we added the ability to give country-code or IP-range
entries in the EntryNodes set, but now that we did, it is.
(Fix: We now shuffle the entry nodes before adding them; only
add up to 10*NumEntryGuards)
* We didn't screen EntryNodes for the Guard flag. That's okay
if the user has specified two or three entry nodes manually,
but if they have listed a whole subcontinent, we should
restrict ourselves to the entries that are currently guards.
(Fix: separate out the new guard from the new non-guard nodes,
and add the Guards first.)
* We'd prepend new EntryNodes _before_ the already configured
EntryNodes. This could lead to churn.
(Fix: don't prepend these.)
This patch also pre-screens EntryNodes entries for
reachableaddresses/excludenodes, even though we check for that
later. This is important now, since we cap the number of entries
we'll add.
All of the routerset_contains*() functions return 0 if their
routerset_t argument is NULL. Therefore, there's no point in
doing "if (ExcludeNodes && routerset_contains*(ExcludeNodes...))",
for example.
This patch fixes every instance of
if (X && routerstatus_contains*(X,...))
Note that there are other patterns that _aren't_ redundant. For
example, we *don't* want to change:
if (EntryNodes && !routerstatus_contains(EntryNodes,...))
Fixes#2797. No bug here; just needless code.
Returning a tristate is needless here; we can just use the yielded
transport/proxy_type field to tell whether there's a proxy, and have
the return indicate success/failure.
Also, store the proxy_type in the or_connection_t rather than letting
it get out of sync if a configuration reload happens between launching
the or_connection and deciding what to say with it.
- const-ify some transport_t pointers
- Remove a vestigial argument to parse_bridge_line
- Make it compile without warnings on my laptop with
--enable-gcc-warnings
