Right now it says "552 internal error" because there's no way for
getinfo_helper_*() countries to specify an error message. This
patch changes the getinfo_helper_*() interface, and makes most of the
getinfo helpers give useful error messages in response to failures.
This should prevent recurrences of bug 1699, where a missing GeoIPFile
line in the torrc made GETINFO ip-to-county/* fail in a "not obvious
how to fix" way.
We now record large times as abandoned, to prevent a filter step from
happening and skewing our results.
Also, issue a warn for a rare case that can happen for funky values of Xm or
too many abandoned circuits. Can happen (very rarely) during unit tests, but
should not be possble during live operation, due to network liveness filters
and discard logic.
Many friendly operating systems have 64-bit times, and it's not nice
to pass them to an %ld format.
It's also extremely not-nice to write a time to the log as an
integer. Most people think it's 2010 June 29 23:57 UTC+epsilon, not
1277855805+epsilon.
We need to record different statistics at point of timeout, vs the point
of forcible closing.
Also, give some better names to constants and state file variables
to indicate they are not dealing with timeouts, but abandoned circuits.
There are now four ways that CBT can be disabled:
1. Network-wide, with the cbtdisabled consensus param.
2. Via config, with "LearnCircuitBuildTimeout 0"
3. Via config, with "AuthoritativeDirectory 1"
4. Via a state file write failure.
This should prevent some asserts and storage of incorrect build times
for the cases where Tor is suspended during a circuit construction, or
just after completing a circuit. The idea is that if the circuit
build time is much greater than we would have cut it off at, we probably
had a suspend event along this codepath, and we should discard the
value.
In case we decide that the timeout rate is now too high due to our
change of the max synthetic quantile value, this consensus parameter
will allow us to restore it to the previous value.
This is for the other issue we saw in Bug 1335. A large number of high
timeouts were causing the timeout calculation to slowly drift upwards,
especially in conditions of load. This fix repeatedly regenerates all of
our synthetic timeouts whenever the timeout changes, to try to prevent
drift.
It also lowers the timeout cap to help for some cases of Bug 1245, where
some timeout values were so large that we ended up allocating a ton of
scratch memory to count the histogram bins.
The downside is that lowering this cap is affecting our timeout rate.
Unfortunately, the buildtimeout quantile is now higher than the actual
completion rate by what appears to be about 7-10%, which probably
represents the skew in the distribution due to lowering this synthetic
cap.
In my state files, I was seeing several peaks, probably due to different
guards having different latency. This change is meant to better capture
this behavior and generate more reasonable timeouts when it happens. It
is improving the timeout values for my collection of state files.
Another dereference-then-NULL-check sequence. No reports of this bug
triggered in the wild. Fixes bugreport 1256.
Thanks to ekir for discovering and reporting this bug.
asprintf() is a GNU extension that some BSDs have picked up: it does a printf
into a newly allocated chunk of RAM.
Our tor_asprintf() differs from standard asprintf() in that:
- Like our other malloc functions, it asserts on OOM.
- It works on windows.
- It always sets its return-field.
Specifically, there are two cases: a) are we willing to start a new
circuit at a node not in your ExitNodes config option, and b) are we
willing to make use of a circuit that's already established but has an
unsuitable exit.
Now we discard all your circuits when you set ExitNodes, so the only
way you could end up with an exit circuit that ends at an unsuitable
place is if we explicitly ran out of exit nodes, StrictNodes was 0,
and we built this circuit to solve a stream that needs solving.
Fixes bug in dc322931, which would ignore the just-built circuit because
it has an unsuitable exit.
Before it would prepend your requested entrynodes to your list of guard
nodes, but feel free to use others after that. Now it chooses only
from your EntryNodes if any of those are available, and only falls back
to others if a) they're all down and b) StrictNodes is not set.
Also, now we refresh your entry guards from EntryNode at each consensus
fetch (rather than just at startup and then they slowly rot as the
network changes).
The goal here is to make users less likely to set StrictNodes, since
it's doing closer to what they expect it should be doing.
The new rule is: safe_str_X() means "this string is a piece of X
information; make it safe to log." safe_str() on its own means
"this string is a piece of who-knows-what; make it safe to log".
Some *_free functions threw asserts when passed NULL. Now all of them
accept NULL as input and perform no action when called that way.
This gains us consistence for our free functions, and allows some
code simplifications where an explicit null check is no longer necessary.
In C, the code "char x[10]; if (x) {...}" always takes the true branch of
the if statement. Coverity notices this now.
In some cases, we were testing arrays to make sure that an operation
we wanted to do would suceed. Those cases are now always-true.
In some cases, we were testing arrays to see if something was _set_.
Those caes are now tests for strlen(s), or tests for
!tor_mem_is_zero(d,len).
This seems to be happening to me a lot on a garbage DSL line.
We may need to come up with 2 threshholds: a high short onehop
count and a lower longer count.
Don't count one-hop circuits when we're estimating how long it
takes circuits to build on average. Otherwise we'll set our circuit
build timeout lower than we should. Bugfix on 0.2.2.2-alpha.
A) We were considering a circuit had timed out in the special cases
where we close rendezvous circuits because the final rendezvous
circuit couldn't be built in time.
B) We were looking at the wrong timestamp_created when considering
a timeout.
We want it to be under our control so it doesn't mess
up initialization. This is likely the cause for
the bug the previous assert-adding commit (09a75ad) was
trying to address.
Using CircuitBuildTimeout is prone to issues with SIGHUP, etc.
Also, shuffle the circuit build times array after loading it
in so that newer measurements don't replace chunks of
similarly timed measurements.
