mirror of
https://gitlab.torproject.org/tpo/core/tor.git
synced 2024-12-11 05:03:34 +01:00
735 lines
32 KiB
Plaintext
735 lines
32 KiB
Plaintext
|
$Id$
|
||
|
|
||
|
Tor Protocol Specification
|
||
|
|
||
|
Roger Dingledine
|
||
|
Nick Mathewson
|
||
|
|
||
|
Note: This document specifies Tor as currently implemented in versions
|
||
|
0.1.2.1-alpha and earlier. Current protocol designs are described in
|
||
|
tor-spec.txt.
|
||
|
|
||
|
0. Preliminaries
|
||
|
|
||
|
0.1. Notation and encoding
|
||
|
|
||
|
PK -- a public key.
|
||
|
SK -- a private key.
|
||
|
K -- a key for a symmetric cypher.
|
||
|
|
||
|
a|b -- concatenation of 'a' and 'b'.
|
||
|
|
||
|
[A0 B1 C2] -- a three-byte sequence, containing the bytes with
|
||
|
hexadecimal values A0, B1, and C2, in that order.
|
||
|
|
||
|
All numeric values are encoded in network (big-endian) order.
|
||
|
|
||
|
H(m) -- a cryptographic hash of m.
|
||
|
|
||
|
0.2. Security parameters
|
||
|
|
||
|
Tor uses a stream cipher, a public-key cipher, the Diffie-Hellman
|
||
|
protocol, and a hash function.
|
||
|
|
||
|
KEY_LEN -- the length of the stream cipher's key, in bytes.
|
||
|
|
||
|
PK_ENC_LEN -- the length of a public-key encrypted message, in bytes.
|
||
|
PK_PAD_LEN -- the number of bytes added in padding for public-key
|
||
|
encryption, in bytes. (The largest number of bytes that can be encrypted
|
||
|
in a single public-key operation is therefore PK_ENC_LEN-PK_PAD_LEN.)
|
||
|
|
||
|
DH_LEN -- the number of bytes used to represent a member of the
|
||
|
Diffie-Hellman group.
|
||
|
DH_SEC_LEN -- the number of bytes used in a Diffie-Hellman private key (x).
|
||
|
|
||
|
HASH_LEN -- the length of the hash function's output, in bytes.
|
||
|
|
||
|
CELL_LEN -- The length of a Tor cell, in bytes.
|
||
|
|
||
|
0.3. Ciphers
|
||
|
|
||
|
For a stream cipher, we use 128-bit AES in counter mode, with an IV of all
|
||
|
0 bytes.
|
||
|
|
||
|
For a public-key cipher, we use RSA with 1024-bit keys and a fixed
|
||
|
exponent of 65537. We use OAEP padding, with SHA-1 as its digest
|
||
|
function. (For OAEP padding, see
|
||
|
ftp://ftp.rsasecurity.com/pub/pkcs/pkcs-1/pkcs-1v2-1.pdf)
|
||
|
|
||
|
For Diffie-Hellman, we use a generator (g) of 2. For the modulus (p), we
|
||
|
use the 1024-bit safe prime from rfc2409, (section 6.2) whose hex
|
||
|
representation is:
|
||
|
|
||
|
"FFFFFFFFFFFFFFFFC90FDAA22168C234C4C6628B80DC1CD129024E08"
|
||
|
"8A67CC74020BBEA63B139B22514A08798E3404DDEF9519B3CD3A431B"
|
||
|
"302B0A6DF25F14374FE1356D6D51C245E485B576625E7EC6F44C42E9"
|
||
|
"A637ED6B0BFF5CB6F406B7EDEE386BFB5A899FA5AE9F24117C4B1FE6"
|
||
|
"49286651ECE65381FFFFFFFFFFFFFFFF"
|
||
|
|
||
|
As an optimization, implementations SHOULD choose DH private keys (x) of
|
||
|
320 bits. Implementations that do this MUST never use any DH key more
|
||
|
than once.
|
||
|
|
||
|
For a hash function, we use SHA-1.
|
||
|
|
||
|
KEY_LEN=16.
|
||
|
DH_LEN=128; DH_GROUP_LEN=40.
|
||
|
PK_ENC_LEN=128; PK_PAD_LEN=42.
|
||
|
HASH_LEN=20.
|
||
|
|
||
|
When we refer to "the hash of a public key", we mean the SHA-1 hash of the
|
||
|
DER encoding of an ASN.1 RSA public key (as specified in PKCS.1).
|
||
|
|
||
|
All "random" values should be generated with a cryptographically strong
|
||
|
random number generator, unless otherwise noted.
|
||
|
|
||
|
The "hybrid encryption" of a byte sequence M with a public key PK is
|
||
|
computed as follows:
|
||
|
1. If M is less than PK_ENC_LEN-PK_PAD_LEN, pad and encrypt M with PK.
|
||
|
2. Otherwise, generate a KEY_LEN byte random key K.
|
||
|
Let M1 = the first PK_ENC_LEN-PK_PAD_LEN-KEY_LEN bytes of M,
|
||
|
and let M2 = the rest of M.
|
||
|
Pad and encrypt K|M1 with PK. Encrypt M2 with our stream cipher,
|
||
|
using the key K. Concatenate these encrypted values.
|
||
|
[XXX Note that this "hybrid encryption" approach does not prevent
|
||
|
an attacker from adding or removing bytes to the end of M. It also
|
||
|
allows attackers to modify the bytes not covered by the OAEP --
|
||
|
see Goldberg's PET2006 paper for details. We will add a MAC to this
|
||
|
scheme one day. -RD]
|
||
|
|
||
|
0.4. Other parameter values
|
||
|
|
||
|
CELL_LEN=512
|
||
|
|
||
|
1. System overview
|
||
|
|
||
|
Tor is a distributed overlay network designed to anonymize
|
||
|
low-latency TCP-based applications such as web browsing, secure shell,
|
||
|
and instant messaging. Clients choose a path through the network and
|
||
|
build a ``circuit'', in which each node (or ``onion router'' or ``OR'')
|
||
|
in the path knows its predecessor and successor, but no other nodes in
|
||
|
the circuit. Traffic flowing down the circuit is sent in fixed-size
|
||
|
``cells'', which are unwrapped by a symmetric key at each node (like
|
||
|
the layers of an onion) and relayed downstream.
|
||
|
|
||
|
2. Connections
|
||
|
|
||
|
There are two ways to connect to an onion router (OR). The first is
|
||
|
as an onion proxy (OP), which allows the OP to authenticate the OR
|
||
|
without authenticating itself. The second is as another OR, which
|
||
|
allows mutual authentication.
|
||
|
|
||
|
Tor uses TLS for link encryption. All implementations MUST support
|
||
|
the TLS ciphersuite "TLS_EDH_RSA_WITH_DES_192_CBC3_SHA", and SHOULD
|
||
|
support "TLS_DHE_RSA_WITH_AES_128_CBC_SHA" if it is available.
|
||
|
Implementations MAY support other ciphersuites, but MUST NOT
|
||
|
support any suite without ephemeral keys, symmetric keys of at
|
||
|
least KEY_LEN bits, and digests of at least HASH_LEN bits.
|
||
|
|
||
|
An OP or OR always sends a two-certificate chain, consisting of a
|
||
|
certificate using a short-term connection key and a second, self-
|
||
|
signed certificate containing the OR's identity key. The commonName of the
|
||
|
first certificate is the OR's nickname, and the commonName of the second
|
||
|
certificate is the OR's nickname, followed by a space and the string
|
||
|
"<identity>".
|
||
|
|
||
|
All parties receiving certificates must confirm that the identity key is
|
||
|
as expected. (When initiating a connection, the expected identity key is
|
||
|
the one given in the directory; when creating a connection because of an
|
||
|
EXTEND cell, the expected identity key is the one given in the cell.) If
|
||
|
the key is not as expected, the party must close the connection.
|
||
|
|
||
|
All parties SHOULD reject connections to or from ORs that have malformed
|
||
|
or missing certificates. ORs MAY accept or reject connections from OPs
|
||
|
with malformed or missing certificates.
|
||
|
|
||
|
Once a TLS connection is established, the two sides send cells
|
||
|
(specified below) to one another. Cells are sent serially. All
|
||
|
cells are CELL_LEN bytes long. Cells may be sent embedded in TLS
|
||
|
records of any size or divided across TLS records, but the framing
|
||
|
of TLS records MUST NOT leak information about the type or contents
|
||
|
of the cells.
|
||
|
|
||
|
TLS connections are not permanent. An OP or an OR may close a
|
||
|
connection to an OR if there are no circuits running over the
|
||
|
connection, and an amount of time (KeepalivePeriod, defaults to 5
|
||
|
minutes) has passed.
|
||
|
|
||
|
(As an exception, directory servers may try to stay connected to all of
|
||
|
the ORs -- though this will be phased out for the Tor 0.1.2.x release.)
|
||
|
|
||
|
3. Cell Packet format
|
||
|
|
||
|
The basic unit of communication for onion routers and onion
|
||
|
proxies is a fixed-width "cell". Each cell contains the following
|
||
|
fields:
|
||
|
|
||
|
CircID [2 bytes]
|
||
|
Command [1 byte]
|
||
|
Payload (padded with 0 bytes) [CELL_LEN-3 bytes]
|
||
|
[Total size: CELL_LEN bytes]
|
||
|
|
||
|
The CircID field determines which circuit, if any, the cell is
|
||
|
associated with.
|
||
|
|
||
|
The 'Command' field holds one of the following values:
|
||
|
0 -- PADDING (Padding) (See Sec 6.2)
|
||
|
1 -- CREATE (Create a circuit) (See Sec 4.1)
|
||
|
2 -- CREATED (Acknowledge create) (See Sec 4.1)
|
||
|
3 -- RELAY (End-to-end data) (See Sec 4.5 and 5)
|
||
|
4 -- DESTROY (Stop using a circuit) (See Sec 4.4)
|
||
|
5 -- CREATE_FAST (Create a circuit, no PK) (See Sec 4.1)
|
||
|
6 -- CREATED_FAST (Circuit created, no PK) (See Sec 4.1)
|
||
|
7 -- HELLO (Introduce the OR) (See Sec 7.1)
|
||
|
|
||
|
The interpretation of 'Payload' depends on the type of the cell.
|
||
|
PADDING: Payload is unused.
|
||
|
CREATE: Payload contains the handshake challenge.
|
||
|
CREATED: Payload contains the handshake response.
|
||
|
RELAY: Payload contains the relay header and relay body.
|
||
|
DESTROY: Payload contains a reason for closing the circuit.
|
||
|
(see 4.4)
|
||
|
Upon receiving any other value for the command field, an OR must
|
||
|
drop the cell.
|
||
|
|
||
|
The payload is padded with 0 bytes.
|
||
|
|
||
|
PADDING cells are currently used to implement connection keepalive.
|
||
|
If there is no other traffic, ORs and OPs send one another a PADDING
|
||
|
cell every few minutes.
|
||
|
|
||
|
CREATE, CREATED, and DESTROY cells are used to manage circuits;
|
||
|
see section 4 below.
|
||
|
|
||
|
RELAY cells are used to send commands and data along a circuit; see
|
||
|
section 5 below.
|
||
|
|
||
|
HELLO cells are used to introduce parameters and characteristics of
|
||
|
Tor clients and servers when connections are established.
|
||
|
|
||
|
4. Circuit management
|
||
|
|
||
|
4.1. CREATE and CREATED cells
|
||
|
|
||
|
Users set up circuits incrementally, one hop at a time. To create a
|
||
|
new circuit, OPs send a CREATE cell to the first node, with the
|
||
|
first half of the DH handshake; that node responds with a CREATED
|
||
|
cell with the second half of the DH handshake plus the first 20 bytes
|
||
|
of derivative key data (see section 4.2). To extend a circuit past
|
||
|
the first hop, the OP sends an EXTEND relay cell (see section 5)
|
||
|
which instructs the last node in the circuit to send a CREATE cell
|
||
|
to extend the circuit.
|
||
|
|
||
|
The payload for a CREATE cell is an 'onion skin', which consists
|
||
|
of the first step of the DH handshake data (also known as g^x).
|
||
|
This value is hybrid-encrypted (see 0.3) to Bob's public key, giving
|
||
|
an onion-skin of:
|
||
|
PK-encrypted:
|
||
|
Padding padding [PK_PAD_LEN bytes]
|
||
|
Symmetric key [KEY_LEN bytes]
|
||
|
First part of g^x [PK_ENC_LEN-PK_PAD_LEN-KEY_LEN bytes]
|
||
|
Symmetrically encrypted:
|
||
|
Second part of g^x [DH_LEN-(PK_ENC_LEN-PK_PAD_LEN-KEY_LEN)
|
||
|
bytes]
|
||
|
|
||
|
The relay payload for an EXTEND relay cell consists of:
|
||
|
Address [4 bytes]
|
||
|
Port [2 bytes]
|
||
|
Onion skin [DH_LEN+KEY_LEN+PK_PAD_LEN bytes]
|
||
|
Identity fingerprint [HASH_LEN bytes]
|
||
|
|
||
|
The port and address field denote the IPV4 address and port of the next
|
||
|
onion router in the circuit; the public key hash is the hash of the PKCS#1
|
||
|
ASN1 encoding of the next onion router's identity (signing) key. (See 0.3
|
||
|
above.) (Including this hash allows the extending OR verify that it is
|
||
|
indeed connected to the correct target OR, and prevents certain
|
||
|
man-in-the-middle attacks.)
|
||
|
|
||
|
The payload for a CREATED cell, or the relay payload for an
|
||
|
EXTENDED cell, contains:
|
||
|
DH data (g^y) [DH_LEN bytes]
|
||
|
Derivative key data (KH) [HASH_LEN bytes] <see 4.2 below>
|
||
|
|
||
|
The CircID for a CREATE cell is an arbitrarily chosen 2-byte integer,
|
||
|
selected by the node (OP or OR) that sends the CREATE cell. To prevent
|
||
|
CircID collisions, when one OR sends a CREATE cell to another, it chooses
|
||
|
from only one half of the possible values based on the ORs' public
|
||
|
identity keys: if the sending OR has a lower key, it chooses a CircID with
|
||
|
an MSB of 0; otherwise, it chooses a CircID with an MSB of 1.
|
||
|
|
||
|
Public keys are compared numerically by modulus.
|
||
|
|
||
|
As usual with DH, x and y MUST be generated randomly.
|
||
|
|
||
|
4.1.1. CREATE_FAST/CREATED_FAST cells
|
||
|
|
||
|
When initializing the first hop of a circuit, the OP has already
|
||
|
established the OR's identity and negotiated a secret key using TLS.
|
||
|
Because of this, it is not always necessary for the OP to perform the
|
||
|
public key operations to create a circuit. In this case, the
|
||
|
OP MAY send a CREATE_FAST cell instead of a CREATE cell for the first
|
||
|
hop only. The OR responds with a CREATED_FAST cell, and the circuit is
|
||
|
created.
|
||
|
|
||
|
A CREATE_FAST cell contains:
|
||
|
|
||
|
Key material (X) [HASH_LEN bytes]
|
||
|
|
||
|
A CREATED_FAST cell contains:
|
||
|
|
||
|
Key material (Y) [HASH_LEN bytes]
|
||
|
Derivative key data [HASH_LEN bytes] (See 4.2 below)
|
||
|
|
||
|
The values of X and Y must be generated randomly.
|
||
|
|
||
|
[Versions of Tor before 0.1.0.6-rc did not support these cell types;
|
||
|
clients should not send CREATE_FAST cells to older Tor servers.]
|
||
|
|
||
|
4.2. Setting circuit keys
|
||
|
|
||
|
Once the handshake between the OP and an OR is completed, both can
|
||
|
now calculate g^xy with ordinary DH. Before computing g^xy, both client
|
||
|
and server MUST verify that the received g^x or g^y value is not degenerate;
|
||
|
that is, it must be strictly greater than 1 and strictly less than p-1
|
||
|
where p is the DH modulus. Implementations MUST NOT complete a handshake
|
||
|
with degenerate keys. Implementations MUST NOT discard other "weak"
|
||
|
g^x values.
|
||
|
|
||
|
(Discarding degenerate keys is critical for security; if bad keys
|
||
|
are not discarded, an attacker can substitute the server's CREATED
|
||
|
cell's g^y with 0 or 1, thus creating a known g^xy and impersonating
|
||
|
the server. Discarding other keys may allow attacks to learn bits of
|
||
|
the private key.)
|
||
|
|
||
|
(The mainline Tor implementation, in the 0.1.1.x-alpha series, discarded
|
||
|
all g^x values less than 2^24, greater than p-2^24, or having more than
|
||
|
1024-16 identical bits. This served no useful purpose, and we stopped.)
|
||
|
|
||
|
If CREATE or EXTEND is used to extend a circuit, the client and server
|
||
|
base their key material on K0=g^xy, represented as a big-endian unsigned
|
||
|
integer.
|
||
|
|
||
|
If CREATE_FAST is used, the client and server base their key material on
|
||
|
K0=X|Y.
|
||
|
|
||
|
From the base key material K0, they compute KEY_LEN*2+HASH_LEN*3 bytes of
|
||
|
derivative key data as
|
||
|
K = H(K0 | [00]) | H(K0 | [01]) | H(K0 | [02]) | ...
|
||
|
|
||
|
The first HASH_LEN bytes of K form KH; the next HASH_LEN form the forward
|
||
|
digest Df; the next HASH_LEN 41-60 form the backward digest Db; the next
|
||
|
KEY_LEN 61-76 form Kf, and the final KEY_LEN form Kb. Excess bytes from K
|
||
|
are discarded.
|
||
|
|
||
|
KH is used in the handshake response to demonstrate knowledge of the
|
||
|
computed shared key. Df is used to seed the integrity-checking hash
|
||
|
for the stream of data going from the OP to the OR, and Db seeds the
|
||
|
integrity-checking hash for the data stream from the OR to the OP. Kf
|
||
|
is used to encrypt the stream of data going from the OP to the OR, and
|
||
|
Kb is used to encrypt the stream of data going from the OR to the OP.
|
||
|
|
||
|
4.3. Creating circuits
|
||
|
|
||
|
When creating a circuit through the network, the circuit creator
|
||
|
(OP) performs the following steps:
|
||
|
|
||
|
1. Choose an onion router as an exit node (R_N), such that the onion
|
||
|
router's exit policy includes at least one pending stream that
|
||
|
needs a circuit (if there are any).
|
||
|
|
||
|
2. Choose a chain of (N-1) onion routers
|
||
|
(R_1...R_N-1) to constitute the path, such that no router
|
||
|
appears in the path twice.
|
||
|
|
||
|
3. If not already connected to the first router in the chain,
|
||
|
open a new connection to that router.
|
||
|
|
||
|
4. Choose a circID not already in use on the connection with the
|
||
|
first router in the chain; send a CREATE cell along the
|
||
|
connection, to be received by the first onion router.
|
||
|
|
||
|
5. Wait until a CREATED cell is received; finish the handshake
|
||
|
and extract the forward key Kf_1 and the backward key Kb_1.
|
||
|
|
||
|
6. For each subsequent onion router R (R_2 through R_N), extend
|
||
|
the circuit to R.
|
||
|
|
||
|
To extend the circuit by a single onion router R_M, the OP performs
|
||
|
these steps:
|
||
|
|
||
|
1. Create an onion skin, encrypted to R_M's public key.
|
||
|
|
||
|
2. Send the onion skin in a relay EXTEND cell along
|
||
|
the circuit (see section 5).
|
||
|
|
||
|
3. When a relay EXTENDED cell is received, verify KH, and
|
||
|
calculate the shared keys. The circuit is now extended.
|
||
|
|
||
|
When an onion router receives an EXTEND relay cell, it sends a CREATE
|
||
|
cell to the next onion router, with the enclosed onion skin as its
|
||
|
payload. The initiating onion router chooses some circID not yet
|
||
|
used on the connection between the two onion routers. (But see
|
||
|
section 4.1. above, concerning choosing circIDs based on
|
||
|
lexicographic order of nicknames.)
|
||
|
|
||
|
When an onion router receives a CREATE cell, if it already has a
|
||
|
circuit on the given connection with the given circID, it drops the
|
||
|
cell. Otherwise, after receiving the CREATE cell, it completes the
|
||
|
DH handshake, and replies with a CREATED cell. Upon receiving a
|
||
|
CREATED cell, an onion router packs it payload into an EXTENDED relay
|
||
|
cell (see section 5), and sends that cell up the circuit. Upon
|
||
|
receiving the EXTENDED relay cell, the OP can retrieve g^y.
|
||
|
|
||
|
(As an optimization, OR implementations may delay processing onions
|
||
|
until a break in traffic allows time to do so without harming
|
||
|
network latency too greatly.)
|
||
|
|
||
|
4.4. Tearing down circuits
|
||
|
|
||
|
Circuits are torn down when an unrecoverable error occurs along
|
||
|
the circuit, or when all streams on a circuit are closed and the
|
||
|
circuit's intended lifetime is over. Circuits may be torn down
|
||
|
either completely or hop-by-hop.
|
||
|
|
||
|
To tear down a circuit completely, an OR or OP sends a DESTROY
|
||
|
cell to the adjacent nodes on that circuit, using the appropriate
|
||
|
direction's circID.
|
||
|
|
||
|
Upon receiving an outgoing DESTROY cell, an OR frees resources
|
||
|
associated with the corresponding circuit. If it's not the end of
|
||
|
the circuit, it sends a DESTROY cell for that circuit to the next OR
|
||
|
in the circuit. If the node is the end of the circuit, then it tears
|
||
|
down any associated edge connections (see section 5.1).
|
||
|
|
||
|
After a DESTROY cell has been processed, an OR ignores all data or
|
||
|
destroy cells for the corresponding circuit.
|
||
|
|
||
|
To tear down part of a circuit, the OP may send a RELAY_TRUNCATE cell
|
||
|
signaling a given OR (Stream ID zero). That OR sends a DESTROY
|
||
|
cell to the next node in the circuit, and replies to the OP with a
|
||
|
RELAY_TRUNCATED cell.
|
||
|
|
||
|
When an unrecoverable error occurs along one connection in a
|
||
|
circuit, the nodes on either side of the connection should, if they
|
||
|
are able, act as follows: the node closer to the OP should send a
|
||
|
RELAY_TRUNCATED cell towards the OP; the node farther from the OP
|
||
|
should send a DESTROY cell down the circuit.
|
||
|
|
||
|
The payload of a RELAY_TRUNCATED or DESTROY cell contains a single octet,
|
||
|
describing why the circuit is being closed or truncated. When sending a
|
||
|
TRUNCATED or DESTROY cell because of another TRUNCATED or DESTROY cell,
|
||
|
the error code should be propagated. The origin of a circuit always sets
|
||
|
this error code to 0, to avoid leaking its version.
|
||
|
|
||
|
The error codes are:
|
||
|
0 -- NONE (No reason given.)
|
||
|
1 -- PROTOCOL (Tor protocol violation.)
|
||
|
2 -- INTERNAL (Internal error.)
|
||
|
3 -- REQUESTED (A client sent a TRUNCATE command.)
|
||
|
4 -- HIBERNATING (Not currently operating; trying to save bandwidth.)
|
||
|
5 -- RESOURCELIMIT (Out of memory, sockets, or circuit IDs.)
|
||
|
6 -- CONNECTFAILED (Unable to reach server.)
|
||
|
7 -- OR_IDENTITY (Connected to server, but its OR identity was not
|
||
|
as expected.)
|
||
|
8 -- OR_CONN_CLOSED (The OR connection that was carrying this circuit
|
||
|
died.)
|
||
|
|
||
|
[Versions of Tor prior to 0.1.0.11 didn't send reasons; implementations
|
||
|
MUST accept empty TRUNCATED and DESTROY cells.]
|
||
|
|
||
|
4.5. Routing relay cells
|
||
|
|
||
|
When an OR receives a RELAY cell, it checks the cell's circID and
|
||
|
determines whether it has a corresponding circuit along that
|
||
|
connection. If not, the OR drops the RELAY cell.
|
||
|
|
||
|
Otherwise, if the OR is not at the OP edge of the circuit (that is,
|
||
|
either an 'exit node' or a non-edge node), it de/encrypts the payload
|
||
|
with the stream cipher, as follows:
|
||
|
'Forward' relay cell (same direction as CREATE):
|
||
|
Use Kf as key; decrypt.
|
||
|
'Back' relay cell (opposite direction from CREATE):
|
||
|
Use Kb as key; encrypt.
|
||
|
Note that in counter mode, decrypt and encrypt are the same operation.
|
||
|
|
||
|
The OR then decides whether it recognizes the relay cell, by
|
||
|
inspecting the payload as described in section 5.1 below. If the OR
|
||
|
recognizes the cell, it processes the contents of the relay cell.
|
||
|
Otherwise, it passes the decrypted relay cell along the circuit if
|
||
|
the circuit continues. If the OR at the end of the circuit
|
||
|
encounters an unrecognized relay cell, an error has occurred: the OR
|
||
|
sends a DESTROY cell to tear down the circuit.
|
||
|
|
||
|
When a relay cell arrives at an OP, the OP decrypts the payload
|
||
|
with the stream cipher as follows:
|
||
|
OP receives data cell:
|
||
|
For I=N...1,
|
||
|
Decrypt with Kb_I. If the payload is recognized (see
|
||
|
section 5.1), then stop and process the payload.
|
||
|
|
||
|
For more information, see section 5 below.
|
||
|
|
||
|
5. Application connections and stream management
|
||
|
|
||
|
5.1. Relay cells
|
||
|
|
||
|
Within a circuit, the OP and the exit node use the contents of
|
||
|
RELAY packets to tunnel end-to-end commands and TCP connections
|
||
|
("Streams") across circuits. End-to-end commands can be initiated
|
||
|
by either edge; streams are initiated by the OP.
|
||
|
|
||
|
The payload of each unencrypted RELAY cell consists of:
|
||
|
Relay command [1 byte]
|
||
|
'Recognized' [2 bytes]
|
||
|
StreamID [2 bytes]
|
||
|
Digest [4 bytes]
|
||
|
Length [2 bytes]
|
||
|
Data [CELL_LEN-14 bytes]
|
||
|
|
||
|
The relay commands are:
|
||
|
1 -- RELAY_BEGIN [forward]
|
||
|
2 -- RELAY_DATA [forward or backward]
|
||
|
3 -- RELAY_END [forward or backward]
|
||
|
4 -- RELAY_CONNECTED [backward]
|
||
|
5 -- RELAY_SENDME [forward or backward]
|
||
|
6 -- RELAY_EXTEND [forward]
|
||
|
7 -- RELAY_EXTENDED [backward]
|
||
|
8 -- RELAY_TRUNCATE [forward]
|
||
|
9 -- RELAY_TRUNCATED [backward]
|
||
|
10 -- RELAY_DROP [forward or backward]
|
||
|
11 -- RELAY_RESOLVE [forward]
|
||
|
12 -- RELAY_RESOLVED [backward]
|
||
|
|
||
|
Commands labelled as "forward" must only be sent by the originator
|
||
|
of the circuit. Commands labelled as "backward" must only be sent by
|
||
|
other nodes in the circuit back to the originator. Commands marked
|
||
|
as either can be sent either by the originator or other nodes.
|
||
|
|
||
|
The 'recognized' field in any unencrypted relay payload is always set
|
||
|
to zero; the 'digest' field is computed as the first four bytes of
|
||
|
the running digest of all the bytes that have been destined for
|
||
|
this hop of the circuit or originated from this hop of the circuit,
|
||
|
seeded from Df or Db respectively (obtained in section 4.2 above),
|
||
|
and including this RELAY cell's entire payload (taken with the digest
|
||
|
field set to zero).
|
||
|
|
||
|
When the 'recognized' field of a RELAY cell is zero, and the digest
|
||
|
is correct, the cell is considered "recognized" for the purposes of
|
||
|
decryption (see section 4.5 above).
|
||
|
|
||
|
(The digest does not include any bytes from relay cells that do
|
||
|
not start or end at this hop of the circuit. That is, it does not
|
||
|
include forwarded data. Therefore if 'recognized' is zero but the
|
||
|
digest does not match, the running digest at that node should
|
||
|
not be updated, and the cell should be forwarded on.)
|
||
|
|
||
|
All RELAY cells pertaining to the same tunneled stream have the
|
||
|
same stream ID. StreamIDs are chosen arbitrarily by the OP. RELAY
|
||
|
cells that affect the entire circuit rather than a particular
|
||
|
stream use a StreamID of zero.
|
||
|
|
||
|
The 'Length' field of a relay cell contains the number of bytes in
|
||
|
the relay payload which contain real payload data. The remainder of
|
||
|
the payload is padded with NUL bytes.
|
||
|
|
||
|
If the RELAY cell is recognized but the relay command is not
|
||
|
understood, the cell must be dropped and ignored. Its contents
|
||
|
still count with respect to the digests, though. [Before
|
||
|
0.1.1.10, Tor closed circuits when it received an unknown relay
|
||
|
command. Perhaps this will be more forward-compatible. -RD]
|
||
|
|
||
|
5.2. Opening streams and transferring data
|
||
|
|
||
|
To open a new anonymized TCP connection, the OP chooses an open
|
||
|
circuit to an exit that may be able to connect to the destination
|
||
|
address, selects an arbitrary StreamID not yet used on that circuit,
|
||
|
and constructs a RELAY_BEGIN cell with a payload encoding the address
|
||
|
and port of the destination host. The payload format is:
|
||
|
|
||
|
ADDRESS | ':' | PORT | [00]
|
||
|
|
||
|
where ADDRESS can be a DNS hostname, or an IPv4 address in
|
||
|
dotted-quad format, or an IPv6 address surrounded by square brackets;
|
||
|
and where PORT is encoded in decimal.
|
||
|
|
||
|
[What is the [00] for? -NM]
|
||
|
[It's so the payload is easy to parse out with string funcs -RD]
|
||
|
|
||
|
Upon receiving this cell, the exit node resolves the address as
|
||
|
necessary, and opens a new TCP connection to the target port. If the
|
||
|
address cannot be resolved, or a connection can't be established, the
|
||
|
exit node replies with a RELAY_END cell. (See 5.4 below.)
|
||
|
Otherwise, the exit node replies with a RELAY_CONNECTED cell, whose
|
||
|
payload is in one of the following formats:
|
||
|
The IPv4 address to which the connection was made [4 octets]
|
||
|
A number of seconds (TTL) for which the address may be cached [4 octets]
|
||
|
or
|
||
|
Four zero-valued octets [4 octets]
|
||
|
An address type (6) [1 octet]
|
||
|
The IPv6 address to which the connection was made [16 octets]
|
||
|
A number of seconds (TTL) for which the address may be cached [4 octets]
|
||
|
[XXXX Versions of Tor before 0.1.1.6 ignore and do not generate the TTL
|
||
|
field. No version of Tor currently generates the IPv6 format.
|
||
|
|
||
|
Tor servers before 0.1.2.0 set the TTL field to a fixed value. Later
|
||
|
versions set the TTL to the last value seen from a DNS server, and expire
|
||
|
their own cached entries after a fixed interval. This prevents certain
|
||
|
attacks.]
|
||
|
|
||
|
The OP waits for a RELAY_CONNECTED cell before sending any data.
|
||
|
Once a connection has been established, the OP and exit node
|
||
|
package stream data in RELAY_DATA cells, and upon receiving such
|
||
|
cells, echo their contents to the corresponding TCP stream.
|
||
|
RELAY_DATA cells sent to unrecognized streams are dropped.
|
||
|
|
||
|
Relay RELAY_DROP cells are long-range dummies; upon receiving such
|
||
|
a cell, the OR or OP must drop it.
|
||
|
|
||
|
5.3. Closing streams
|
||
|
|
||
|
When an anonymized TCP connection is closed, or an edge node
|
||
|
encounters error on any stream, it sends a 'RELAY_END' cell along the
|
||
|
circuit (if possible) and closes the TCP connection immediately. If
|
||
|
an edge node receives a 'RELAY_END' cell for any stream, it closes
|
||
|
the TCP connection completely, and sends nothing more along the
|
||
|
circuit for that stream.
|
||
|
|
||
|
The payload of a RELAY_END cell begins with a single 'reason' byte to
|
||
|
describe why the stream is closing, plus optional data (depending on
|
||
|
the reason.) The values are:
|
||
|
|
||
|
1 -- REASON_MISC (catch-all for unlisted reasons)
|
||
|
2 -- REASON_RESOLVEFAILED (couldn't look up hostname)
|
||
|
3 -- REASON_CONNECTREFUSED (remote host refused connection) [*]
|
||
|
4 -- REASON_EXITPOLICY (OR refuses to connect to host or port)
|
||
|
5 -- REASON_DESTROY (Circuit is being destroyed)
|
||
|
6 -- REASON_DONE (Anonymized TCP connection was closed)
|
||
|
7 -- REASON_TIMEOUT (Connection timed out, or OR timed out
|
||
|
while connecting)
|
||
|
8 -- (unallocated) [**]
|
||
|
9 -- REASON_HIBERNATING (OR is temporarily hibernating)
|
||
|
10 -- REASON_INTERNAL (Internal error at the OR)
|
||
|
11 -- REASON_RESOURCELIMIT (OR has no resources to fulfill request)
|
||
|
12 -- REASON_CONNRESET (Connection was unexpectedly reset)
|
||
|
13 -- REASON_TORPROTOCOL (Sent when closing connection because of
|
||
|
Tor protocol violations.)
|
||
|
|
||
|
(With REASON_EXITPOLICY, the 4-byte IPv4 address or 16-byte IPv6 address
|
||
|
forms the optional data; no other reason currently has extra data.
|
||
|
As of 0.1.1.6, the body also contains a 4-byte TTL.)
|
||
|
|
||
|
OPs and ORs MUST accept reasons not on the above list, since future
|
||
|
versions of Tor may provide more fine-grained reasons.
|
||
|
|
||
|
[*] Older versions of Tor also send this reason when connections are
|
||
|
reset.
|
||
|
[**] Due to a bug in versions of Tor through 0095, error reason 8 must
|
||
|
remain allocated until that version is obsolete.
|
||
|
|
||
|
--- [The rest of this section describes unimplemented functionality.]
|
||
|
|
||
|
Because TCP connections can be half-open, we follow an equivalent
|
||
|
to TCP's FIN/FIN-ACK/ACK protocol to close streams.
|
||
|
|
||
|
An exit connection can have a TCP stream in one of three states:
|
||
|
'OPEN', 'DONE_PACKAGING', and 'DONE_DELIVERING'. For the purposes
|
||
|
of modeling transitions, we treat 'CLOSED' as a fourth state,
|
||
|
although connections in this state are not, in fact, tracked by the
|
||
|
onion router.
|
||
|
|
||
|
A stream begins in the 'OPEN' state. Upon receiving a 'FIN' from
|
||
|
the corresponding TCP connection, the edge node sends a 'RELAY_FIN'
|
||
|
cell along the circuit and changes its state to 'DONE_PACKAGING'.
|
||
|
Upon receiving a 'RELAY_FIN' cell, an edge node sends a 'FIN' to
|
||
|
the corresponding TCP connection (e.g., by calling
|
||
|
shutdown(SHUT_WR)) and changing its state to 'DONE_DELIVERING'.
|
||
|
|
||
|
When a stream in already in 'DONE_DELIVERING' receives a 'FIN', it
|
||
|
also sends a 'RELAY_FIN' along the circuit, and changes its state
|
||
|
to 'CLOSED'. When a stream already in 'DONE_PACKAGING' receives a
|
||
|
'RELAY_FIN' cell, it sends a 'FIN' and changes its state to
|
||
|
'CLOSED'.
|
||
|
|
||
|
If an edge node encounters an error on any stream, it sends a
|
||
|
'RELAY_END' cell (if possible) and closes the stream immediately.
|
||
|
|
||
|
5.4. Remote hostname lookup
|
||
|
|
||
|
To find the address associated with a hostname, the OP sends a
|
||
|
RELAY_RESOLVE cell containing the hostname to be resolved. (For a reverse
|
||
|
lookup, the OP sends a RELAY_RESOLVE cell containing an in-addr.arpa
|
||
|
address.) The OR replies with a RELAY_RESOLVED cell containing a status
|
||
|
byte, and any number of answers. Each answer is of the form:
|
||
|
Type (1 octet)
|
||
|
Length (1 octet)
|
||
|
Value (variable-width)
|
||
|
TTL (4 octets)
|
||
|
"Length" is the length of the Value field.
|
||
|
"Type" is one of:
|
||
|
0x00 -- Hostname
|
||
|
0x04 -- IPv4 address
|
||
|
0x06 -- IPv6 address
|
||
|
0xF0 -- Error, transient
|
||
|
0xF1 -- Error, nontransient
|
||
|
|
||
|
If any answer has a type of 'Error', then no other answer may be given.
|
||
|
|
||
|
The RELAY_RESOLVE cell must use a nonzero, distinct streamID; the
|
||
|
corresponding RELAY_RESOLVED cell must use the same streamID. No stream
|
||
|
is actually created by the OR when resolving the name.
|
||
|
|
||
|
6. Flow control
|
||
|
|
||
|
6.1. Link throttling
|
||
|
|
||
|
Each node should do appropriate bandwidth throttling to keep its
|
||
|
user happy.
|
||
|
|
||
|
Communicants rely on TCP's default flow control to push back when they
|
||
|
stop reading.
|
||
|
|
||
|
6.2. Link padding
|
||
|
|
||
|
Currently nodes are not required to do any sort of link padding or
|
||
|
dummy traffic. Because strong attacks exist even with link padding,
|
||
|
and because link padding greatly increases the bandwidth requirements
|
||
|
for running a node, we plan to leave out link padding until this
|
||
|
tradeoff is better understood.
|
||
|
|
||
|
6.3. Circuit-level flow control
|
||
|
|
||
|
To control a circuit's bandwidth usage, each OR keeps track of
|
||
|
two 'windows', consisting of how many RELAY_DATA cells it is
|
||
|
allowed to package for transmission, and how many RELAY_DATA cells
|
||
|
it is willing to deliver to streams outside the network.
|
||
|
Each 'window' value is initially set to 1000 data cells
|
||
|
in each direction (cells that are not data cells do not affect
|
||
|
the window). When an OR is willing to deliver more cells, it sends a
|
||
|
RELAY_SENDME cell towards the OP, with Stream ID zero. When an OR
|
||
|
receives a RELAY_SENDME cell with stream ID zero, it increments its
|
||
|
packaging window.
|
||
|
|
||
|
Each of these cells increments the corresponding window by 100.
|
||
|
|
||
|
The OP behaves identically, except that it must track a packaging
|
||
|
window and a delivery window for every OR in the circuit.
|
||
|
|
||
|
An OR or OP sends cells to increment its delivery window when the
|
||
|
corresponding window value falls under some threshold (900).
|
||
|
|
||
|
If a packaging window reaches 0, the OR or OP stops reading from
|
||
|
TCP connections for all streams on the corresponding circuit, and
|
||
|
sends no more RELAY_DATA cells until receiving a RELAY_SENDME cell.
|
||
|
[this stuff is badly worded; copy in the tor-design section -RD]
|
||
|
|
||
|
6.4. Stream-level flow control
|
||
|
|
||
|
Edge nodes use RELAY_SENDME cells to implement end-to-end flow
|
||
|
control for individual connections across circuits. Similarly to
|
||
|
circuit-level flow control, edge nodes begin with a window of cells
|
||
|
(500) per stream, and increment the window by a fixed value (50)
|
||
|
upon receiving a RELAY_SENDME cell. Edge nodes initiate RELAY_SENDME
|
||
|
cells when both a) the window is <= 450, and b) there are less than
|
||
|
ten cell payloads remaining to be flushed at that edge.
|
||
|
|