tor/doc/spec/dir-spec.txt

2422 lines
101 KiB
Plaintext
Raw Normal View History

Tor directory protocol, version 3
0. Scope and preliminaries
This directory protocol is used by Tor version 0.2.0.x-alpha and later.
See dir-spec-v1.txt for information on the protocol used up to the
0.1.0.x series, and dir-spec-v2.txt for information on the protocol
used by the 0.1.1.x and 0.1.2.x series.
Caches and authorities must still support older versions of the
directory protocols, until the versions of Tor that require them are
2010-03-15 20:41:59 +01:00
finally out of commission.
This document merges and supersedes the following proposals:
101 Voting on the Tor Directory System
103 Splitting identity key from regularly used signing key
104 Long and Short Router Descriptors
XXX when to download certificates.
XXX timeline
XXX fill in XXXXs
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
RFC 2119.
0.1. History
The earliest versions of Onion Routing shipped with a list of known
routers and their keys. When the set of routers changed, users needed to
fetch a new list.
The Version 1 Directory protocol
--------------------------------
Early versions of Tor (0.0.2) introduced "Directory authorities": servers
that served signed "directory" documents containing a list of signed
"router descriptors", along with short summary of the status of each
router. Thus, clients could get up-to-date information on the state of
the network automatically, and be certain that the list they were getting
was attested by a trusted directory authority.
Later versions (0.0.8) added directory caches, which download
directories from the authorities and serve them to clients. Non-caches
fetch from the caches in preference to fetching from the authorities, thus
distributing bandwidth requirements.
Also added during the version 1 directory protocol were "router status"
documents: short documents that listed only the up/down status of the
routers on the network, rather than a complete list of all the
descriptors. Clients and caches would fetch these documents far more
frequently than they would fetch full directories.
The Version 2 Directory Protocol
--------------------------------
During the Tor 0.1.1.x series, Tor revised its handling of directory
documents in order to address two major problems:
* Directories had grown quite large (over 1MB), and most directory
downloads consisted mainly of router descriptors that clients
already had.
* Every directory authority was a trust bottleneck: if a single
directory authority lied, it could make clients believe for a time
an arbitrarily distorted view of the Tor network. (Clients
trusted the most recent signed document they downloaded.) Thus,
adding more authorities would make the system less secure, not
more.
To address these, we extended the directory protocol so that
authorities now published signed "network status" documents. Each
network status listed, for every router in the network: a hash of its
identity key, a hash of its most recent descriptor, and a summary of
what the authority believed about its status. Clients would download
the authorities' network status documents in turn, and believe
statements about routers iff they were attested to by more than half of
the authorities.
Instead of downloading all router descriptors at once, clients
downloaded only the descriptors that they did not have. Descriptors
were indexed by their digests, in order to prevent malicious caches
from giving different versions of a router descriptor to different
clients.
Routers began working harder to upload new descriptors only when their
contents were substantially changed.
0.2. Goals of the version 3 protocol
Version 3 of the Tor directory protocol tries to solve the following
issues:
* A great deal of bandwidth used to transmit router descriptors was
used by two fields that are not actually used by Tor routers
(namely read-history and write-history). We save about 60% by
moving them into a separate document that most clients do not
fetch or use.
* It was possible under certain perverse circumstances for clients
to download an unusual set of network status documents, thus
partitioning themselves from clients who have a more recent and/or
typical set of documents. Even under the best of circumstances,
clients were sensitive to the ages of the network status documents
they downloaded. Therefore, instead of having the clients
correlate multiple network status documents, we have the
authorities collectively vote on a single consensus network status
document.
* The most sensitive data in the entire network (the identity keys
of the directory authorities) needed to be stored unencrypted so
2007-05-04 09:22:11 +02:00
that the authorities can sign network-status documents on the fly.
Now, the authorities' identity keys are stored offline, and used
to certify medium-term signing keys that can be rotated.
0.3. Some Remaining questions
Things we could solve on a v3 timeframe:
The SHA-1 hash is showing its age. We should do something about our
dependency on it. We could probably future-proof ourselves here in
this revision, at least so far as documents from the authorities are
concerned.
Too many things about the authorities are hardcoded by IP.
Perhaps we should start accepting longer identity keys for routers
too.
Things to solve eventually:
Requiring every client to know about every router won't scale forever.
Requiring every directory cache to know every router won't scale
forever.
1. Outline
There is a small set (say, around 5-10) of semi-trusted directory
authorities. A default list of authorities is shipped with the Tor
software. Users can change this list, but are encouraged not to do so,
in order to avoid partitioning attacks.
Every authority has a very-secret, long-term "Authority Identity Key".
This is stored encrypted and/or offline, and is used to sign "key
certificate" documents. Every key certificate contains a medium-term
(3-12 months) "authority signing key", that is used by the authority to
sign other directory information. (Note that the authority identity
key is distinct from the router identity key that the authority uses
in its role as an ordinary router.)
Routers periodically upload signed "routers descriptors" to the
directory authorities describing their keys, capabilities, and other
information. Routers may also upload signed "extra info documents"
containing information that is not required for the Tor protocol.
Directory authorities serve router descriptors indexed by router
identity, or by hash of the descriptor.
Routers may act as directory caches to reduce load on the directory
authorities. They announce this in their descriptors.
Periodically, each directory authority generates a view of
the current descriptors and status for known routers. They send a
signed summary of this view (a "status vote") to the other
authorities. The authorities compute the result of this vote, and sign
a "consensus status" document containing the result of the vote.
Directory caches download, cache, and re-serve consensus documents.
Clients, directory caches, and directory authorities all use consensus
documents to find out when their list of routers is out-of-date.
(Directory authorities also use vote statuses.) If it is, they download
any missing router descriptors. Clients download missing descriptors
from caches; caches and authorities download from authorities.
Descriptors are downloaded by the hash of the descriptor, not by the
server's identity key: this prevents servers from attacking clients by
giving them descriptors nobody else uses.
All directory information is uploaded and downloaded with HTTP.
[Authorities also generate and caches also cache documents produced and
2010-03-15 20:41:59 +01:00
used by earlier versions of this protocol; see dir-spec-v1.txt and
dir-spec-v2.txt for notes on those versions.]
1.1. What's different from version 2?
Clients used to download multiple network status documents,
corresponding roughly to "status votes" above. They would compute the
result of the vote on the client side.
Authorities used to sign documents using the same private keys they used
for their roles as routers. This forced them to keep these extremely
sensitive keys in memory unencrypted.
All of the information in extra-info documents used to be kept in the
main descriptors.
1.2. Document meta-format
Router descriptors, directories, and running-routers documents all obey the
following lightweight extensible information format.
The highest level object is a Document, which consists of one or more
Items. Every Item begins with a KeywordLine, followed by zero or more
Objects. A KeywordLine begins with a Keyword, optionally followed by
whitespace and more non-newline characters, and ends with a newline. A
Keyword is a sequence of one or more characters in the set [A-Za-z0-9-].
An Object is a block of encoded data in pseudo-Open-PGP-style
armor. (cf. RFC 2440)
More formally:
NL = The ascii LF character (hex value 0x0a).
Document ::= (Item | NL)+
Item ::= KeywordLine Object*
KeywordLine ::= Keyword NL | Keyword WS ArgumentChar+ NL
Keyword = KeywordChar+
KeywordChar ::= 'A' ... 'Z' | 'a' ... 'z' | '0' ... '9' | '-'
ArgumentChar ::= any printing ASCII character except NL.
WS = (SP | TAB)+
Object ::= BeginLine Base-64-encoded-data EndLine
BeginLine ::= "-----BEGIN " Keyword "-----" NL
EndLine ::= "-----END " Keyword "-----" NL
The BeginLine and EndLine of an Object must use the same keyword.
When interpreting a Document, software MUST ignore any KeywordLine that
starts with a keyword it doesn't recognize; future implementations MUST NOT
require current clients to understand any KeywordLine not currently
described.
The "opt" keyword was used until Tor 0.1.2.5-alpha for non-critical future
extensions. All implementations MUST ignore any item of the form "opt
keyword ....." when they would not recognize "keyword ....."; and MUST
treat "opt keyword ....." as synonymous with "keyword ......" when keyword
is recognized.
Implementations before 0.1.2.5-alpha rejected any document with a
KeywordLine that started with a keyword that they didn't recognize.
When generating documents that need to be read by older versions of Tor,
implementations MUST prefix items not recognized by older versions of
Tor with an "opt" until those versions of Tor are obsolete. [Note that
key certificates, status vote documents, extra info documents, and
status consensus documents will never be read by older versions of Tor.]
Other implementations that want to extend Tor's directory format MAY
introduce their own items. The keywords for extension items SHOULD start
with the characters "x-" or "X-", to guarantee that they will not conflict
with keywords used by future versions of Tor.
In our document descriptions below, we tag Items with a multiplicity in
brackets. Possible tags are:
"At start, exactly once": These items MUST occur in every instance of
the document type, and MUST appear exactly once, and MUST be the
first item in their documents.
"Exactly once": These items MUST occur exactly one time in every
instance of the document type.
2007-05-04 09:22:11 +02:00
"At end, exactly once": These items MUST occur in every instance of
the document type, and MUST appear exactly once, and MUST be the
last item in their documents.
"At most once": These items MAY occur zero or one times in any
instance of the document type, but MUST NOT occur more than once.
"Any number": These items MAY occur zero, one, or more times in any
instance of the document type.
"Once or more": These items MUST occur at least once in any instance
of the document type, and MAY occur more.
1.3. Signing documents
Every signable document below is signed in a similar manner, using a
given "Initial Item", a final "Signature Item", a digest algorithm, and
a signing key.
The Initial Item must be the first item in the document.
The Signature Item has the following format:
<signature item keyword> [arguments] NL SIGNATURE NL
The "SIGNATURE" Object contains a signature (using the signing key) of
the PKCS1-padded digest of the entire document, taken from the
beginning of the Initial item, through the newline after the Signature
Item's keyword and its arguments.
Unless otherwise, the digest algorithm is SHA-1.
All documents are invalid unless signed with the correct signing key.
The "Digest" of a document, unless stated otherwise, is its digest *as
signed by this signature scheme*.
1.4. Voting timeline
Every consensus document has a "valid-after" (VA) time, a "fresh-until"
(FU) time and a "valid-until" (VU) time. VA MUST precede FU, which MUST
in turn precede VU. Times are chosen so that every consensus will be
"fresh" until the next consensus becomes valid, and "valid" for a while
after. At least 3 consensuses should be valid at any given time.
The timeline for a given consensus is as follows:
VA-DistSeconds-VoteSeconds: The authorities exchange votes.
VA-DistSeconds-VoteSeconds/2: The authorities try to download any
votes they don't have.
VA-DistSeconds: The authorities calculate the consensus and exchange
signatures.
VA-DistSeconds/2: The authorities try to download any signatures
they don't have.
VA: All authorities have a multiply signed consensus.
VA ... FU: Caches download the consensus. (Note that since caches have
no way of telling what VA and FU are until they have downloaded
2007-11-29 17:16:50 +01:00
the consensus, they assume that the present consensus's VA is
equal to the previous one's FU, and that its FU is one interval after
that.)
2007-10-19 04:31:43 +02:00
FU: The consensus is no longer the freshest consensus.
FU ... (the current consensus's VU): Clients download the consensus.
(See note above: clients guess that the next consensus's FU will be
two intervals after the current VA.)
VU: The consensus is no longer valid.
VoteSeconds and DistSeconds MUST each be at least 20 seconds; FU-VA and
VU-FU MUST each be at least 5 minutes.
2. Router operation and formats
ORs SHOULD generate a new router descriptor and a new extra-info
document whenever any of the following events have occurred:
- A period of time (18 hrs by default) has passed since the last
time a descriptor was generated.
- A descriptor field other than bandwidth or uptime has changed.
- Bandwidth has changed by a factor of 2 from the last time a
descriptor was generated, and at least a given interval of time
(20 mins by default) has passed since then.
- Its uptime has been reset (by restarting).
[XXX this list is incomplete; see router_differences_are_cosmetic()
in routerlist.c for others]
ORs SHOULD NOT publish a new router descriptor or extra-info document
if none of the above events have occurred and not much time has passed
(12 hours by default).
After generating a descriptor, ORs upload them to every directory
authority they know, by posting them (in order) to the URL
http://<hostname:port>/tor/
2.1. Router descriptor format
Router descriptors consist of the following items. For backward
compatibility, there should be an extra NL at the end of each router
descriptor.
In lines that take multiple arguments, extra arguments SHOULD be
accepted and ignored. Many of the nonterminals below are defined in
section 2.3.
"router" nickname address ORPort SOCKSPort DirPort NL
[At start, exactly once.]
Indicates the beginning of a router descriptor. "nickname" must be a
valid router nickname as specified in 2.3. "address" must be an IPv4
address in dotted-quad format. The last three numbers indicate the
TCP ports at which this OR exposes functionality. ORPort is a port at
which this OR accepts TLS connections for the main OR protocol;
SOCKSPort is deprecated and should always be 0; and DirPort is the
port at which this OR accepts directory-related HTTP connections. If
any port is not supported, the value 0 is given instead of a port
number. (At least one of DirPort and ORPort SHOULD be set;
authorities MAY reject any descriptor with both DirPort and ORPort of
0.)
"bandwidth" bandwidth-avg bandwidth-burst bandwidth-observed NL
[Exactly once]
Estimated bandwidth for this router, in bytes per second. The
"average" bandwidth is the volume per second that the OR is willing to
sustain over long periods; the "burst" bandwidth is the volume that
the OR is willing to sustain in very short intervals. The "observed"
value is an estimate of the capacity this server can handle. The
server remembers the max bandwidth sustained output over any ten
second period in the past day, and another sustained input. The
"observed" value is the lesser of these two numbers.
"platform" string NL
[At most once]
A human-readable string describing the system on which this OR is
running. This MAY include the operating system, and SHOULD include
the name and version of the software implementing the Tor protocol.
"published" YYYY-MM-DD HH:MM:SS NL
[Exactly once]
The time, in GMT, when this descriptor (and its corresponding
extra-info document if any) was generated.
"fingerprint" fingerprint NL
[At most once]
A fingerprint (a HASH_LEN-byte of asn1 encoded public key, encoded in
hex, with a single space after every 4 characters) for this router's
identity key. A descriptor is considered invalid (and MUST be
rejected) if the fingerprint line does not match the public key.
[We didn't start parsing this line until Tor 0.1.0.6-rc; it should
be marked with "opt" until earlier versions of Tor are obsolete.]
"hibernating" bool NL
[At most once]
If the value is 1, then the Tor server was hibernating when the
descriptor was published, and shouldn't be used to build circuits.
[We didn't start parsing this line until Tor 0.1.0.6-rc; it should be
marked with "opt" until earlier versions of Tor are obsolete.]
"uptime" number NL
[At most once]
The number of seconds that this OR process has been running.
"onion-key" NL a public key in PEM format
[Exactly once]
This key is used to encrypt EXTEND cells for this OR. The key MUST be
accepted for at least 1 week after any new key is published in a
subsequent descriptor. It MUST be 1024 bits.
"signing-key" NL a public key in PEM format
[Exactly once]
The OR's long-term identity key. It MUST be 1024 bits.
"accept" exitpattern NL
"reject" exitpattern NL
[Any number]
These lines describe an "exit policy": the rules that an OR follows
when deciding whether to allow a new stream to a given address. The
'exitpattern' syntax is described below. There MUST be at least one
such entry. The rules are considered in order; if no rule matches,
the address will be accepted. For clarity, the last such entry SHOULD
be accept *:* or reject *:*.
"router-signature" NL Signature NL
[At end, exactly once]
The "SIGNATURE" object contains a signature of the PKCS1-padded
hash of the entire router descriptor, taken from the beginning of the
"router" line, through the newline after the "router-signature" line.
The router descriptor is invalid unless the signature is performed
with the router's identity key.
"contact" info NL
[At most once]
Describes a way to contact the server's administrator, preferably
including an email address and a PGP key fingerprint.
"family" names NL
[At most once]
'Names' is a space-separated list of server nicknames or
hexdigests. If two ORs list one another in their "family" entries,
then OPs should treat them as a single OR for the purpose of path
selection.
For example, if node A's descriptor contains "family B", and node B's
descriptor contains "family A", then node A and node B should never
be used on the same circuit.
"read-history" YYYY-MM-DD HH:MM:SS (NSEC s) NUM,NUM,NUM,NUM,NUM... NL
[At most once]
"write-history" YYYY-MM-DD HH:MM:SS (NSEC s) NUM,NUM,NUM,NUM,NUM... NL
[At most once]
Declare how much bandwidth the OR has used recently. Usage is divided
into intervals of NSEC seconds. The YYYY-MM-DD HH:MM:SS field
defines the end of the most recent interval. The numbers are the
number of bytes used in the most recent intervals, ordered from
oldest to newest.
[We didn't start parsing these lines until Tor 0.1.0.6-rc; they should
be marked with "opt" until earlier versions of Tor are obsolete.]
[See also migration notes in section 2.2.1.]
"eventdns" bool NL
[At most once]
Declare whether this version of Tor is using the newer enhanced
dns logic. Versions of Tor with this field set to false SHOULD NOT
be used for reverse hostname lookups.
[All versions of Tor before 0.1.2.2-alpha should be assumed to have
this option set to 0 if it is not present. All Tor versions at
0.1.2.2-alpha or later should be assumed to have this option set to
1 if it is not present. Until 0.1.2.1-alpha-dev, this option was
not generated, even when the new DNS code was in use. Versions of Tor
before 0.1.2.1-alpha-dev did not parse this option, so it should be
marked "opt". The dnsworker logic has been removed, so this option
should not be used by new server code. However, it can still be
used, and should still be recognized by new code until Tor 0.1.2.x
is obsolete.]
"caches-extra-info" NL
[At most once.]
Present only if this router is a directory cache that provides
extra-info documents.
[Versions before 0.2.0.1-alpha don't recognize this, and versions
before 0.1.2.5-alpha will reject descriptors containing it unless
it is prefixed with "opt"; it should be so prefixed until these
versions are obsolete.]
"extra-info-digest" digest NL
[At most once]
"Digest" is a hex-encoded digest (using upper-case characters) of the
router's extra-info document, as signed in the router's extra-info
(that is, not including the signature). (If this field is absent, the
router is not uploading a corresponding extra-info document.)
[Versions before 0.2.0.1-alpha don't recognize this, and versions
before 0.1.2.5-alpha will reject descriptors containing it unless
it is prefixed with "opt"; it should be so prefixed until these
versions are obsolete.]
"hidden-service-dir" *(SP VersionNum) NL
2007-11-29 13:51:50 +01:00
[At most once.]
Present only if this router stores and serves hidden service
descriptors. If any VersionNum(s) are specified, this router
supports those descriptor versions. If none are specified, it
defaults to version 2 descriptors.
2007-11-29 13:51:50 +01:00
[Versions of Tor before 0.1.2.5-alpha rejected router descriptors
with unrecognized items; the protocols line should be preceded with
an "opt" until these Tors are obsolete.]
"protocols" SP "Link" SP LINK-VERSION-LIST SP "Circuit" SP
CIRCUIT-VERSION-LIST NL
[At most once.]
Both lists are space-separated sequences of numbers, to indicate which
protocols the server supports. As of 30 Mar 2008, specified
protocols are "Link 1 2 Circuit 1". See section 4.1 of tor-spec.txt
for more information about link protocol versions.
[Versions of Tor before 0.1.2.5-alpha rejected router descriptors
with unrecognized items; the protocols line should be preceded with
an "opt" until these Tors are obsolete.]
"allow-single-hop-exits" NL
2009-08-26 20:48:13 +02:00
[At most once.]
Present only if the router allows single-hop circuits to make exit
connections. Most Tor servers do not support this: this is
included for specialized controllers designed to support perspective
access and such.
2.2. Extra-info documents
Extra-info documents consist of the following items:
"extra-info" Nickname Fingerprint NL
[At start, exactly once.]
Identifies what router this is an extra info descriptor for.
Fingerprint is encoded in hex (using upper-case letters), with
no spaces.
"published" YYYY-MM-DD HH:MM:SS NL
[Exactly once.]
The time, in GMT, when this document (and its corresponding router
descriptor if any) was generated. It MUST match the published time
in the corresponding router descriptor.
"read-history" YYYY-MM-DD HH:MM:SS (NSEC s) NUM,NUM,NUM,NUM,NUM... NL
[At most once.]
"write-history" YYYY-MM-DD HH:MM:SS (NSEC s) NUM,NUM,NUM,NUM,NUM... NL
[At most once.]
As documented in 2.1 above. See migration notes in section 2.2.1.
("geoip-start" YYYY-MM-DD HH:MM:SS NL)
("geoip-client-origins" CC=N,CC=N,... NL)
Only generated by bridge routers (see blocking.pdf), and only
when they have been configured with a geoip database.
Non-bridges SHOULD NOT generate these fields. Contains a list
of mappings from two-letter country codes (CC) to the number
of clients that have connected to that bridge from that
country (approximate, and rounded up to the nearest multiple of 8
in order to hamper traffic analysis). A country is included
only if it has at least one address. The time in
"geoip-start" is the time at which we began collecting geoip
statistics.
"geoip-start" and "geoip-client-origins" have been replaced by
"bridge-stats-end" and "bridge-stats-ips" in 0.2.2.4-alpha. The
reason is that the measurement interval with "geoip-stats" as
determined by subtracting "geoip-start" from "published" could
have had a variable length, whereas the measurement interval in
0.2.2.4-alpha and later is set to be exactly 24 hours long. In
order to clearly distinguish the new measurement intervals from
the old ones, the new keywords have been introduced.
"bridge-stats-end" YYYY-MM-DD HH:MM:SS (NSEC s) NL
[At most once.]
YYYY-MM-DD HH:MM:SS defines the end of the included measurement
interval of length NSEC seconds (86400 seconds by default).
A "bridge-stats-end" line, as well as any other "bridge-*" line,
is only added when the relay has been running as a bridge for at
least 24 hours.
"bridge-ips" CC=N,CC=N,... NL
[At most once.]
List of mappings from two-letter country codes to the number of
unique IP addresses that have connected from that country to the
bridge and which are no known relays, rounded up to the nearest
multiple of 8.
2009-08-18 16:14:22 +02:00
"dirreq-stats-end" YYYY-MM-DD HH:MM:SS (NSEC s) NL
[At most once.]
YYYY-MM-DD HH:MM:SS defines the end of the included measurement
interval of length NSEC seconds (86400 seconds by default).
A "dirreq-stats-end" line, as well as any other "dirreq-*" line,
is only added when the relay has opened its Dir port and after 24
hours of measuring directory requests.
"dirreq-v2-ips" CC=N,CC=N,... NL
[At most once.]
"dirreq-v3-ips" CC=N,CC=N,... NL
[At most once.]
List of mappings from two-letter country codes to the number of
unique IP addresses that have connected from that country to
request a v2/v3 network status, rounded up to the nearest multiple
of 8. Only those IP addresses are counted that the directory can
answer with a 200 OK status code.
"dirreq-v2-reqs" CC=N,CC=N,... NL
[At most once.]
"dirreq-v3-reqs" CC=N,CC=N,... NL
[At most once.]
List of mappings from two-letter country codes to the number of
requests for v2/v3 network statuses from that country, rounded up
to the nearest multiple of 8. Only those requests are counted that
the directory can answer with a 200 OK status code.
"dirreq-v2-share" num% NL
[At most once.]
"dirreq-v3-share" num% NL
[At most once.]
The share of v2/v3 network status requests that the directory
expects to receive from clients based on its advertised bandwidth
compared to the overall network bandwidth capacity. Shares are
formatted in percent with two decimal places. Shares are
calculated as means over the whole 24-hour interval.
"dirreq-v2-resp" status=num,... NL
[At most once.]
"dirreq-v3-resp" status=nul,... NL
[At most once.]
List of mappings from response statuses to the number of requests
for v2/v3 network statuses that were answered with that response
status, rounded up to the nearest multiple of 4. Only response
statuses with at least 1 response are reported. New response
statuses can be added at any time. The current list of response
statuses is as follows:
"ok": a network status request is answered; this number
corresponds to the sum of all requests as reported in
"dirreq-v2-reqs" or "dirreq-v3-reqs", respectively, before
rounding up.
"not-enough-sigs: a version 3 network status is not signed by a
sufficient number of requested authorities.
"unavailable": a requested network status object is unavailable.
"not-found": a requested network status is not found.
"not-modified": a network status has not been modified since the
If-Modified-Since time that is included in the request.
"busy": the directory is busy.
"dirreq-v2-direct-dl" key=val,... NL
[At most once.]
"dirreq-v3-direct-dl" key=val,... NL
[At most once.]
"dirreq-v2-tunneled-dl" key=val,... NL
[At most once.]
"dirreq-v3-tunneled-dl" key=val,... NL
[At most once.]
List of statistics about possible failures in the download process
of v2/v3 network statuses. Requests are either "direct"
HTTP-encoded requests over the relay's directory port, or
"tunneled" requests using a BEGIN_DIR cell over the relay's OR
port. The list of possible statistics can change, and statistics
can be left out from reporting. The current list of statistics is
as follows:
Successful downloads and failures:
"complete": a client has finished the download successfully.
"timeout": a download did not finish within 10 minutes after
starting to send the response.
"running": a download is still running at the end of the
measurement period for less than 10 minutes after starting to
send the response.
Download times:
"min", "max": smallest and largest measured bandwidth in B/s.
"d[1-4,6-9]": 1st to 4th and 6th to 9th decile of measured
bandwidth in B/s. For a given decile i, i/10 of all downloads
had a smaller bandwidth than di, and (10-i)/10 of all downloads
had a larger bandwidth than di.
"q[1,3]": 1st and 3rd quartile of measured bandwidth in B/s. One
fourth of all downloads had a smaller bandwidth than q1, one
fourth of all downloads had a larger bandwidth than q3, and the
remaining half of all downloads had a bandwidth between q1 and
q3.
"md": median of measured bandwidth in B/s. Half of the downloads
had a smaller bandwidth than md, the other half had a larger
bandwidth than md.
"dirreq-read-history" YYYY-MM-DD HH:MM:SS (NSEC s) NUM,NUM,NUM... NL
[At most once]
"dirreq-write-history" YYYY-MM-DD HH:MM:SS (NSEC s) NUM,NUM,NUM... NL
[At most once]
Declare how much bandwidth the OR has spent on answering directory
requests. Usage is divided into intervals of NSEC seconds. The
YYYY-MM-DD HH:MM:SS field defines the end of the most recent
interval. The numbers are the number of bytes used in the most
recent intervals, ordered from oldest to newest.
2009-08-18 16:14:22 +02:00
"entry-stats-end" YYYY-MM-DD HH:MM:SS (NSEC s) NL
[At most once.]
YYYY-MM-DD HH:MM:SS defines the end of the included measurement
interval of length NSEC seconds (86400 seconds by default).
An "entry-stats-end" line, as well as any other "entry-*"
line, is first added after the relay has been running for at least
24 hours.
"entry-ips" CC=N,CC=N,... NL
[At most once.]
List of mappings from two-letter country codes to the number of
unique IP addresses that have connected from that country to the
relay and which are no known other relays, rounded up to the
nearest multiple of 8.
"cell-stats-end" YYYY-MM-DD HH:MM:SS (NSEC s) NL
[At most once.]
YYYY-MM-DD HH:MM:SS defines the end of the included measurement
interval of length NSEC seconds (86400 seconds by default).
A "cell-stats-end" line, as well as any other "cell-*" line,
is first added after the relay has been running for at least 24
hours.
"cell-processed-cells" num,...,num NL
[At most once.]
Mean number of processed cells per circuit, subdivided into
deciles of circuits by the number of cells they have processed in
descending order from loudest to quietest circuits.
"cell-queued-cells" num,...,num NL
[At most once.]
Mean number of cells contained in queues by circuit decile. These
means are calculated by 1) determining the mean number of cells in
a single circuit between its creation and its termination and 2)
calculating the mean for all circuits in a given decile as
determined in "cell-processed-cells". Numbers have a precision of
two decimal places.
"cell-time-in-queue" num,...,num NL
[At most once.]
Mean time cells spend in circuit queues in milliseconds. Times are
calculated by 1) determining the mean time cells spend in the
queue of a single circuit and 2) calculating the mean for all
circuits in a given decile as determined in
"cell-processed-cells".
"cell-circuits-per-decile" num NL
[At most once.]
Mean number of circuits that are included in any of the deciles,
rounded up to the next integer.
"exit-stats-end" YYYY-MM-DD HH:MM:SS (NSEC s) NL
[At most once.]
YYYY-MM-DD HH:MM:SS defines the end of the included measurement
interval of length NSEC seconds (86400 seconds by default).
An "exit-stats-end" line, as well as any other "exit-*" line, is
first added after the relay has been running for at least 24 hours
and only if the relay permits exiting (where exiting to a single
port and IP address is sufficient).
"exit-kibibytes-written" port=N,port=N,... NL
[At most once.]
"exit-kibibytes-read" port=N,port=N,... NL
[At most once.]
List of mappings from ports to the number of kibibytes that the
relay has written to or read from exit connections to that port,
rounded up to the next full kibibyte.
"exit-streams-opened" port=N,port=N,... NL
[At most once.]
List of mappings from ports to the number of opened exit streams
to that port, rounded up to the nearest multiple of 4.
"router-signature" NL Signature NL
[At end, exactly once.]
A document signature as documented in section 1.3, using the
initial item "extra-info" and the final item "router-signature",
signed with the router's identity key.
2.2.1. Moving history fields to extra-info documents.
Tools that want to use the read-history and write-history values SHOULD
download extra-info documents as well as router descriptors. Such
tools SHOULD accept history values from both sources; if they appear in
both documents, the values in the extra-info documents are authoritative.
New versions of Tor no longer generate router descriptors
containing read-history or write-history. Tools should continue to
accept read-history and write-history values in router descriptors
produced by older versions of Tor until all Tor versions earlier
than 0.2.0.x are obsolete.
2.3. Nonterminals in router descriptors
nickname ::= between 1 and 19 alphanumeric characters ([A-Za-z0-9]),
case-insensitive.
hexdigest ::= a '$', followed by 40 hexadecimal characters
([A-Fa-f0-9]). [Represents a server by the digest of its identity
key.]
exitpattern ::= addrspec ":" portspec
portspec ::= "*" | port | port "-" port
port ::= an integer between 1 and 65535, inclusive.
[Some implementations incorrectly generate ports with value 0.
Implementations SHOULD accept this, and SHOULD NOT generate it.
Connections to port 0 are never permitted.]
addrspec ::= "*" | ip4spec | ip6spec
ipv4spec ::= ip4 | ip4 "/" num_ip4_bits | ip4 "/" ip4mask
ip4 ::= an IPv4 address in dotted-quad format
ip4mask ::= an IPv4 mask in dotted-quad format
num_ip4_bits ::= an integer between 0 and 32
ip6spec ::= ip6 | ip6 "/" num_ip6_bits
ip6 ::= an IPv6 address, surrounded by square brackets.
num_ip6_bits ::= an integer between 0 and 128
bool ::= "0" | "1"
3. Formats produced by directory authorities.
Every authority has two keys used in this protocol: a signing key, and
an authority identity key. (Authorities also have a router identity
key used in their role as a router and by earlier versions of the
directory protocol.) The identity key is used from time to time to
sign new key certificates using new signing keys; it is very sensitive.
The signing key is used to sign key certificates and status documents.
There are three kinds of documents generated by directory authorities:
Key certificates
Status votes
Status consensuses
Each is discussed below.
3.1. Key certificates
Key certificates consist of the following items:
"dir-key-certificate-version" version NL
[At start, exactly once.]
Determines the version of the key certificate. MUST be "3" for
the protocol described in this document. Implementations MUST
reject formats they don't understand.
"dir-address" IPPort NL
[At most once]
An IP:Port for this authority's directory port.
"fingerprint" fingerprint NL
[Exactly once.]
Hexadecimal encoding without spaces based on the authority's
identity key.
"dir-identity-key" NL a public key in PEM format
[Exactly once.]
The long-term authority identity key for this authority. This key
SHOULD be at least 2048 bits long; it MUST NOT be shorter than
1024 bits.
"dir-key-published" YYYY-MM-DD HH:MM:SS NL
[Exactly once.]
The time (in GMT) when this document and corresponding key were
last generated.
"dir-key-expires" YYYY-MM-DD HH:MM:SS NL
[Exactly once.]
A time (in GMT) after which this key is no longer valid.
"dir-signing-key" NL a key in PEM format
[Exactly once.]
The directory server's public signing key. This key MUST be at
least 1024 bits, and MAY be longer.
"dir-key-crosscert" NL CrossSignature NL
[At most once.]
NOTE: Authorities MUST include this field in all newly generated
certificates. A future version of this specification will make
the field required.
CrossSignature is a signature, made using the certificate's signing
key, of the digest of the PKCS1-padded hash of the certificate's
identity key. For backward compatibility with broken versions of the
parser, we wrap the base64-encoded signature in -----BEGIN ID
SIGNATURE---- and -----END ID SIGNATURE----- tags. Implementations
MUST allow the "ID " portion to be omitted, however.
When encountering a certificate with a dir-key-crosscert entry,
implementations MUST verify that the signature is a correct signature
of the hash of the identity key using the signing key.
"dir-key-certification" NL Signature NL
[At end, exactly once.]
A document signature as documented in section 1.3, using the
initial item "dir-key-certificate-version" and the final item
"dir-key-certification", signed with the authority identity key.
Authorities MUST generate a new signing key and corresponding
certificate before the key expires.
3.2. Vote and consensus status documents
Votes and consensuses are more strictly formatted then other documents
in this specification, since different authorities must be able to
generate exactly the same consensus given the same set of votes.
The procedure for deciding when to generate vote and consensus status
2010-03-15 20:41:59 +01:00
documents are described in section 1.4 on the voting timeline.
Status documents contain a preamble, an authority section, a list of
2009-08-26 20:48:13 +02:00
router status entries, and one or more footer signature, in that order.
Unlike other formats described above, a SP in these documents must be a
single space character (hex 20).
Some items appear only in votes, and some items appear only in
consensuses. Unless specified, items occur in both.
The preamble contains the following items. They MUST occur in the
order given here:
"network-status-version" SP version NL.
[At start, exactly once.]
A document format version. For this specification, the version is
"3".
"vote-status" SP type NL
[Exactly once.]
The status MUST be "vote" or "consensus", depending on the type of
the document.
"consensus-methods" SP IntegerList NL
[Exactly once for votes; does not occur in consensuses.]
A space-separated list of supported methods for generating
consensuses from votes. See section 3.4.1 for details. Method "1"
MUST be included.
"consensus-method" SP Integer NL
[Exactly once for consensuses; does not occur in votes.]
See section 3.4.1 for details.
(Only included when the vote is generated with consensus-method 2 or
later.)
"published" SP YYYY-MM-DD SP HH:MM:SS NL
[Exactly once for votes; does not occur in consensuses.]
The publication time for this status document (if a vote).
"valid-after" SP YYYY-MM-DD SP HH:MM:SS NL
[Exactly once.]
The start of the Interval for this vote. Before this time, the
consensus document produced from this vote should not be used.
See 1.4 for voting timeline information.
"fresh-until" SP YYYY-MM-DD SP HH:MM:SS NL
[Exactly once.]
The time at which the next consensus should be produced; before this
time, there is no point in downloading another consensus, since there
won't be a new one. See 1.4 for voting timeline information.
"valid-until" SP YYYY-MM-DD SP HH:MM:SS NL
[Exactly once.]
The end of the Interval for this vote. After this time, the
consensus produced by this vote should not be used. See 1.4 for
voting timeline information.
"voting-delay" SP VoteSeconds SP DistSeconds NL
[Exactly once.]
VoteSeconds is the number of seconds that we will allow to collect
votes from all authorities; DistSeconds is the number of seconds
we'll allow to collect signatures from all authorities. See 1.4 for
voting timeline information.
"client-versions" SP VersionList NL
[At most once.]
A comma-separated list of recommended client versions, in
ascending order. If absent, no opinion is held about client
versions.
"server-versions" SP VersionList NL
[At most once.]
A comma-separated list of recommended server versions, in
ascending order. If absent, no opinion is held about server
versions.
"known-flags" SP FlagList NL
[Exactly once.]
A space-separated list of all of the flags that this document
might contain. A flag is "known" either because the authority
knows about them and might set them (if in a vote), or because
enough votes were counted for the consensus for an authoritative
opinion to have been formed about their status.
"params" SP [Parameters] NL
[At most once]
Parameter ::= Keyword '=' Int32
Int32 ::= A decimal integer between -2147483648 and 2147483647.
Parameters ::= Parameter | Parameters SP Parameter
The parameters list, if present, contains a space-separated list of
case-sensitive key-value pairs, sorted in lexical order by
their keyword. Each parameter has its own meaning.
(Only included when the vote is generated with consensus-method 7 or
later.)
Commonly used "param" arguments at this point include:
"circwindow" -- the default package window that circuits should
be established with. It started out at 1000 cells, but some
research indicates that a lower value would mean fewer cells in
transit in the network at any given time. Obeyed by Tor 0.2.1.20
and later.
2011-01-15 19:49:39 +01:00
Min: 100, Max: 1000
"CircuitPriorityHalflifeMsec" -- the halflife parameter used when
weighting which circuit will send the next cell. Obeyed by Tor
0.2.2.10-alpha and later. (Versions of Tor between 0.2.2.7-alpha
and 0.2.2.10-alpha recognized a "CircPriorityHalflifeMsec" parameter,
but mishandled it badly.)
2011-01-15 19:49:39 +01:00
Min: -1, Max: 2147483647 (INT32_MAX)
"perconnbwrate" and "perconnbwburst" -- if set, each relay sets
up a separate token bucket for every client OR connection,
and rate limits that connection indepedently. Typically left
unset, except when used for performance experiments around trac
entry 1750. Only honored by relays running Tor 0.2.2.16-alpha
and later. (Note that relays running 0.2.2.7-alpha through
0.2.2.14-alpha looked for bwconnrate and bwconnburst, but then
did the wrong thing with them; see bug 1830 for details.)
Min: 1, Max: 2147483647 (INT32_MAX)
"refuseunknownexits" -- if set to one, exit relays look at
the previous hop of circuits that ask to open an exit stream,
and refuse to exit if they don't recognize it as a relay. The
goal is to make it harder for people to use them as one-hop
proxies. See trac entry 1751 for details.
Min: 0, Max: 1
See also "2.4.5. Consensus parameters governing behavior"
in path-spec.txt for a series of circuit build time related
consensus params.
The authority section of a vote contains the following items, followed
in turn by the authority's current key certificate:
"dir-source" SP nickname SP identity SP address SP IP SP dirport SP
orport NL
[Exactly once, at start]
Describes this authority. The nickname is a convenient identifier
for the authority. The identity is an uppercase hex fingerprint of
the authority's current (v3 authority) identity key. The address is
the server's hostname. The IP is the server's current IP address,
and dirport is its current directory port. XXXXorport
"contact" SP string NL
[At most once.]
An arbitrary string describing how to contact the directory
server's administrator. Administrators should include at least an
email address and a PGP fingerprint.
"legacy-key" SP FINGERPRINT NL
[At most once]
Lists a fingerprint for an obsolete _identity_ key still used
by this authority to keep older clients working. This option
is used to keep key around for a little while in case the
authorities need to migrate many identity keys at once.
(Generally, this would only happen because of a security
vulnerability that affected multiple authorities, like the
Debian OpenSSL RNG bug of May 2008.)
The authority section of a consensus contains groups the following items,
in the order given, with one group for each authority that contributed to
the consensus, with groups sorted by authority identity digest:
"dir-source" SP nickname SP identity SP address SP IP SP dirport SP
orport NL
[Exactly once, at start]
As in the authority section of a vote.
"contact" SP string NL
[At most once.]
As in the authority section of a vote.
"vote-digest" SP digest NL
[Exactly once.]
A digest of the vote from the authority that contributed to this
consensus, as signed (that is, not including the signature).
(Hex, upper-case.)
Each router status entry contains the following items. Router status
entries are sorted in ascending order by identity digest.
"r" SP nickname SP identity SP digest SP publication SP IP SP ORPort
SP DirPort NL
[At start, exactly once.]
"Nickname" is the OR's nickname. "Identity" is a hash of its
identity key, encoded in base64, with trailing equals sign(s)
removed. "Digest" is a hash of its most recent descriptor as
2009-01-18 21:48:43 +01:00
signed (that is, not including the signature), encoded in base64.
"Publication" is the
publication time of its most recent descriptor, in the form
YYYY-MM-DD HH:MM:SS, in GMT. "IP" is its current IP address;
ORPort is its current OR port, "DirPort" is it's current directory
port, or "0" for "none".
"s" SP Flags NL
[At most once.]
A series of space-separated status flags, in alphabetical order.
Currently documented flags are:
"Authority" if the router is a directory authority.
"BadExit" if the router is believed to be useless as an exit node
(because its ISP censors it, because it is behind a restrictive
proxy, or for some similar reason).
"BadDirectory" if the router is believed to be useless as a
2007-01-05 07:03:10 +01:00
directory cache (because its directory port isn't working,
its bandwidth is always throttled, or for some similar
reason).
"Exit" if the router is more useful for building
general-purpose exit circuits than for relay circuits. The
path building algorithm uses this flag; see path-spec.txt.
"Fast" if the router is suitable for high-bandwidth circuits.
2006-01-24 01:48:42 +01:00
"Guard" if the router is suitable for use as an entry guard.
2007-11-29 13:51:50 +01:00
"HSDir" if the router is considered a v2 hidden service directory.
"Named" if the router's identity-nickname mapping is canonical,
and this authority binds names.
"Stable" if the router is suitable for long-lived circuits.
2005-09-14 23:57:59 +02:00
"Running" if the router is currently usable.
"Unnamed" if another router has bound the name used by this
router, and this authority binds names.
"Valid" if the router has been 'validated'.
"V2Dir" if the router implements the v2 directory protocol.
"V3Dir" if the router implements this protocol.
"v" SP version NL
[At most once.]
The version of the Tor protocol that this server is running. If
the value begins with "Tor" SP, the rest of the string is a Tor
version number, and the protocol is "The Tor protocol as supported
by the given version of Tor." Otherwise, if the value begins with
some other string, Tor has upgraded to a more sophisticated
protocol versioning system, and the protocol is "a version of the
Tor protocol more recent than any we recognize."
Directory authorities SHOULD omit version strings they receive from
descriptors if they would cause "v" lines to be over 128 characters
long.
"w" SP "Bandwidth=" INT [SP "Measured=" INT] NL
[At most once.]
An estimate of the bandwidth of this server, in an arbitrary
unit (currently kilobytes per second). Used to weight router
selection.
Additionally, the Measured= keyword is present in votes by
2010-01-12 18:39:39 +01:00
participating bandwidth measurement authorities to indicate
a measured bandwidth currently produced by measuring stream
capacities.
Other weighting keywords may be added later.
Clients MUST ignore keywords they do not recognize.
"p" SP ("accept" / "reject") SP PortList NL
[At most once.]
PortList = PortOrRange
PortList = PortList "," PortOrRange
PortOrRange = INT "-" INT / INT
A list of those ports that this router supports (if 'accept')
or does not support (if 'reject') for exit to "most
addresses".
The footer section is delineated in all votes and consensuses supporting
consensus method 9 and above with the following:
"directory-footer" NL
It contains two subsections, a bandwidths-weights line and a
directory-signature.
The bandwidths-weights line appears At Most Once for a consensus. It does
not appear in votes.
"bandwidth-weights" SP
"Wbd=" INT SP "Wbe=" INT SP "Wbg=" INT SP "Wbm=" INT SP
"Wdb=" INT SP
"Web=" INT SP "Wed=" INT SP "Wee=" INT SP "Weg=" INT SP "Wem=" INT SP
"Wgb=" INT SP "Wgd=" INT SP "Wgg=" INT SP "Wgm=" INT SP
"Wmb=" INT SP "Wmd=" INT SP "Wme=" INT SP "Wmg=" INT SP "Wmm=" INT NL
These values represent the weights to apply to router bandwidths during
path selection. They are sorted in alphabetical order in the list. The
integer values are divided by BW_WEIGHT_SCALE=10000 or the consensus
param "bwweightscale". They are:
Wgg - Weight for Guard-flagged nodes in the guard position
Wgm - Weight for non-flagged nodes in the guard Position
Wgd - Weight for Guard+Exit-flagged nodes in the guard Position
Wmg - Weight for Guard-flagged nodes in the middle Position
Wmm - Weight for non-flagged nodes in the middle Position
Wme - Weight for Exit-flagged nodes in the middle Position
Wmd - Weight for Guard+Exit flagged nodes in the middle Position
Weg - Weight for Guard flagged nodes in the exit Position
Wem - Weight for non-flagged nodes in the exit Position
Wee - Weight for Exit-flagged nodes in the exit Position
Wed - Weight for Guard+Exit-flagged nodes in the exit Position
Wgb - Weight for BEGIN_DIR-supporting Guard-flagged nodes
Wmb - Weight for BEGIN_DIR-supporting non-flagged nodes
Web - Weight for BEGIN_DIR-supporting Exit-flagged nodes
Wdb - Weight for BEGIN_DIR-supporting Guard+Exit-flagged nodes
Wbg - Weight for Guard flagged nodes for BEGIN_DIR requests
Wbm - Weight for non-flagged nodes for BEGIN_DIR requests
Wbe - Weight for Exit-flagged nodes for BEGIN_DIR requests
Wbd - Weight for Guard+Exit-flagged nodes for BEGIN_DIR requests
These values are calculated as specified in Section 3.4.3.
The signature contains the following item, which appears Exactly Once
for a vote, and At Least Once for a consensus.
"directory-signature" SP identity SP signing-key-digest NL Signature
This is a signature of the status document, with the initial item
"network-status-version", and the signature item
"directory-signature", using the signing key. (In this case, we take
the hash through the _space_ after directory-signature, not the
newline: this ensures that all authorities sign the same thing.)
"identity" is the hex-encoded digest of the authority identity key of
the signing authority, and "signing-key-digest" is the hex-encoded
digest of the current authority signing key of the signing authority.
2010-03-13 20:54:05 +01:00
3.3. Assigning flags in a vote
(This section describes how directory authorities choose which status
flags to apply to routers, as of Tor 0.2.0.0-alpha-dev. Later directory
authorities MAY do things differently, so long as clients keep working
well. Clients MUST NOT depend on the exact behaviors in this section.)
In the below definitions, a router is considered "active" if it is
running, valid, and not hibernating.
"Valid" -- a router is 'Valid' if it is running a version of Tor not
known to be broken, and the directory authority has not blacklisted
it as suspicious.
"Named" -- Directory authority administrators may decide to support name
binding. If they do, then they must maintain a file of
nickname-to-identity-key mappings, and try to keep this file consistent
with other directory authorities. If they don't, they act as clients, and
report bindings made by other directory authorities (name X is bound to
identity Y if at least one binding directory lists it, and no directory
binds X to some other Y'.) A router is called 'Named' if the router
believes the given name should be bound to the given key.
Two strategies exist on the current network for deciding on
values for the Named flag. In the original version, server
operators were asked to send nickname-identity pairs to a
mailing list of Naming directory authorities operators. The
operators were then supposed to add the pairs to their
mapping files; in practice, they didn't get to this often.
Newer Naming authorities run a script that registers routers
in their mapping files once the routers have been online at
least two weeks, no other router has that nickname, and no
other router has wanted the nickname for a month. If a router
has not been online for six months, the router is removed.
"Unnamed" -- Directory authorities that support naming should vote for a
2007-10-25 06:17:59 +02:00
router to be 'Unnamed' if its given nickname is mapped to a different
identity.
"Running" -- A router is 'Running' if the authority managed to connect to
it successfully within the last 30 minutes.
"Stable" -- A router is 'Stable' if it is active, and either its Weighted
MTBF is at least the median for known active routers or its Weighted MTBF
corresponds to at least 7 days. Routers are never called Stable if they are
running a version of Tor known to drop circuits stupidly. (0.1.1.10-alpha
through 0.1.1.16-rc are stupid this way.)
To calculate weighted MTBF, compute the weighted mean of the lengths
of all intervals when the router was observed to be up, weighting
intervals by $\alpha^n$, where $n$ is the amount of time that has
passed since the interval ended, and $\alpha$ is chosen so that
measurements over approximately one month old no longer influence the
weighted MTBF much.
[XXXX what happens when we have less than 4 days of MTBF info.]
"Exit" -- A router is called an 'Exit' iff it allows exits to at
least two of the ports 80, 443, and 6667 and allows exits to at
least one /8 address space.
"Fast" -- A router is 'Fast' if it is active, and its bandwidth is
either in the top 7/8ths for known active routers or at least 20KB/s.
"Guard" -- A router is a possible 'Guard' if its Weighted Fractional
Uptime is at least the median for "familiar" active routers, and if
its bandwidth is at least median or at least 250KB/s.
To calculate weighted fractional uptime, compute the fraction
of time that the router is up in any given day, weighting so that
downtime and uptime in the past counts less.
A node is 'familiar' if 1/8 of all active nodes have appeared more
recently than it, OR it has been around for a few weeks.
"Authority" -- A router is called an 'Authority' if the authority
generating the network-status document believes it is an authority.
"V2Dir" -- A router supports the v2 directory protocol if it has an open
directory port, and it is running a version of the directory protocol that
supports the functionality clients need. (Currently, this is
0.1.1.9-alpha or later.)
"V3Dir" -- A router supports the v3 directory protocol if it has an open
directory port, and it is running a version of the directory protocol that
supports the functionality clients need. (Currently, this is
0.2.0.?????-alpha or later.)
2007-11-29 13:51:50 +01:00
"HSDir" -- A router is a v2 hidden service directory if it stores and
serves v2 hidden service descriptors and the authority managed to connect
to it successfully within the last 24 hours.
Directory server administrators may label some servers or IPs as
blacklisted, and elect not to include them in their network-status lists.
Authorities SHOULD 'disable' any servers in excess of 3 on any single IP.
When there are more than 3 to choose from, authorities should first prefer
authorities to non-authorities, then prefer Running to non-Running, and
then prefer high-bandwidth to low-bandwidth. To 'disable' a server, the
authority *should* advertise it without the Running or Valid flag.
Thus, the network-status vote includes all non-blacklisted,
non-expired, non-superseded descriptors.
The bandwidth in a "w" line should be taken as the best estimate
of the router's actual capacity that the authority has. For now,
this should be the lesser of the observed bandwidth and bandwidth
rate limit from the router descriptor. It is given in kilobytes
per second, and capped at some arbitrary value (currently 10 MB/s).
The Measured= keyword on a "w" line vote is currently computed
2010-01-15 21:58:35 +01:00
by multiplying the previous published consensus bandwidth by the
ratio of the measured average node stream capacity to the network
average. If 3 or more authorities provide a Measured= keyword for
a router, the authorities produce a consensus containing a "w"
Bandwidth= keyword equal to the median of the Measured= votes.
The ports listed in a "p" line should be taken as those ports for
which the router's exit policy permits 'most' addresses, ignoring any
accept not for all addresses, ignoring all rejects for private
netblocks. "Most" addresses are permitted if no more than 2^25
IPv4 addresses (two /8 networks) were blocked. The list is encoded
as described in 3.4.2.
3.4. Computing a consensus from a set of votes
Given a set of votes, authorities compute the contents of the consensus
document as follows:
The "valid-after", "valid-until", and "fresh-until" times are taken as
the median of the respective values from all the votes.
The times in the "voting-delay" line are taken as the median of the
VoteSeconds and DistSeconds times in the votes.
Known-flags is the union of all flags known by any voter.
Entries are given on the "params" line for every keyword on which any
authority voted. The values given are the low-median of all votes on
that keyword.
"client-versions" and "server-versions" are sorted in ascending
order; A version is recommended in the consensus if it is recommended
by more than half of the voting authorities that included a
client-versions or server-versions lines in their votes.
The authority item groups (dir-source, contact, fingerprint,
vote-digest) are taken from the votes of the voting
authorities. These groups are sorted by the digests of the
authorities identity keys, in ascending order. If the consensus
method is 3 or later, a dir-source line must be included for
every vote with legacy-key entry, using the legacy-key's
fingerprint, the voter's ordinary nickname with the string
"-legacy" appended, and all other fields as from the original
vote's dir-source line.
A router status entry:
* is included in the result if some router status entry with the same
identity is included by more than half of the authorities (total
authorities, not just those whose votes we have).
* For any given identity, we include at most one router status entry.
* A router entry has a flag set if that is included by more than half
of the authorities who care about that flag.
* Two router entries are "the same" if they have the same
<descriptor digest, published time, nickname, IP, ports> tuple.
We choose the tuple for a given router as whichever tuple appears
for that router in the most votes. We break ties first in favor of
the more recently published, then in favor of smaller server
descriptor digest.
* The Named flag appears if it is included for this routerstatus by
_any_ authority, and if all authorities that list it list the same
2007-10-25 06:17:59 +02:00
nickname. However, if consensus-method 2 or later is in use, and
any authority calls this identity/nickname pair Unnamed, then
this routerstatus does not get the Named flag.
* If consensus-method 2 or later is in use, the Unnamed flag is
set for a routerstatus if any authorities have voted for a different
identities to be Named with that nickname, or if any authority
lists that nickname/ID pair as Unnamed.
(With consensus-method 1, Unnamed is set like any other flag.)
* The version is given as whichever version is listed by the most
voters, with ties decided in favor of more recent versions.
* If consensus-method 4 or later is in use, then routers that
do not have the Running flag are not listed at all.
* If consensus-method 5 or later is in use, then the "w" line
is generated using a low-median of the bandwidth values from
the votes that included "w" lines for this router.
* If consensus-method 5 or later is in use, then the "p" line
is taken from the votes that have the same policy summary
for the descriptor we are listing. (They should all be the
same. If they are not, we pick the most commonly listed
one, breaking ties in favor of the lexicographically larger
vote.) The port list is encoded as specified in 3.4.2.
* If consensus-method 6 or later is in use and if 3 or more
authorities provide a Measured= keyword in their votes for
a router, the authorities produce a consensus containing a
Bandwidth= keyword equal to the median of the Measured= votes.
* If consensus-method 7 or later is in use, the params line is
included in the output.
The signatures at the end of a consensus document are sorted in
ascending order by identity digest.
All ties in computing medians are broken in favor of the smaller or
earlier item.
3.4.1. Forward compatibility
Future versions of Tor will need to include new information in the
consensus documents, but it is important that all authorities (or at least
half) generate and sign the same signed consensus.
To achieve this, authorities list in their votes their supported methods
for generating consensuses from votes. Later methods will be assigned
higher numbers. Currently recognized methods:
"1" -- The first implemented version.
"2" -- Added support for the Unnamed flag.
"3" -- Added legacy ID key support to aid in authority ID key rollovers
"4" -- No longer list routers that are not running in the consensus
"5" -- adds support for "w" and "p" lines.
"6" -- Prefers measured bandwidth values rather than advertised
2010-02-23 03:43:44 +01:00
"7" -- Provides keyword=integer pairs of consensus parameters
"8" -- Provides microdescriptor summaries
"9" -- Provides weights for selecting flagged routers in paths
"10" -- Fixes edge case bugs in router flag selection weights
Before generating a consensus, an authority must decide which consensus
method to use. To do this, it looks for the highest version number
supported by more than 2/3 of the authorities voting. If it supports this
method, then it uses it. Otherwise, it falls back to method 1.
(The consensuses generated by new methods must be parsable by
implementations that only understand the old methods, and must not cause
those implementations to compromise their anonymity. This is a means for
making changes in the contents of consensus; not for making
backward-incompatible changes in their format.)
3.4.2. Encoding port lists
Whether the summary shows the list of accepted ports or the list of
rejected ports depends on which list is shorter (has a shorter string
representation). In case of ties we choose the list of accepted
ports. As an exception to this rule an allow-all policy is
represented as "accept 1-65535" instead of "reject " and a reject-all
policy is similarly given as "reject 1-65535".
Summary items are compressed, that is instead of "80-88,89-100" there
only is a single item of "80-100", similarly instead of "20,21" a
summary will say "20-21".
Port lists are sorted in ascending order.
The maximum allowed length of a policy summary (including the "accept "
or "reject ") is 1000 characters. If a summary exceeds that length we
use an accept-style summary and list as much of the port list as is
possible within these 1000 bytes. [XXXX be more specific.]
3.4.3. Computing Bandwidth Weights
Let weight_scale = 10000
Let G be the total bandwidth for Guard-flagged nodes.
Let M be the total bandwidth for non-flagged nodes.
Let E be the total bandwidth for Exit-flagged nodes.
Let D be the total bandwidth for Guard+Exit-flagged nodes.
Let T = G+M+E+D
Let Wgd be the weight for choosing a Guard+Exit for the guard position.
Let Wmd be the weight for choosing a Guard+Exit for the middle position.
Let Wed be the weight for choosing a Guard+Exit for the exit position.
Let Wme be the weight for choosing an Exit for the middle position.
Let Wmg be the weight for choosing a Guard for the middle position.
Let Wgg be the weight for choosing a Guard for the guard position.
Let Wee be the weight for choosing an Exit for the exit position.
Balanced network conditions then arise from solutions to the following
system of equations:
Wgg*G + Wgd*D == M + Wmd*D + Wme*E + Wmg*G (guard bw = middle bw)
Wgg*G + Wgd*D == Wee*E + Wed*D (guard bw = exit bw)
Wed*D + Wmd*D + Wgd*D == D (aka: Wed+Wmd+Wdg = 1)
Wmg*G + Wgg*G == G (aka: Wgg = 1-Wmg)
Wme*E + Wee*E == E (aka: Wee = 1-Wme)
We are short 2 constraints with the above set. The remaining constraints
come from examining different cases of network load. The following
constraints are used in consensus method 10 and above. There are another
incorrect and obsolete set of constraints used for these same cases in
consensus method 9. For those, see dir-spec.txt in Tor 0.2.2.10-alpha
to 0.2.2.16-alpha.
Case 1: E >= T/3 && G >= T/3 (Neither Exit nor Guard Scarce)
In this case, the additional two constraints are: Wmg == Wmd,
Wed == 1/3.
This leads to the solution:
Wgd = weight_scale/3
Wed = weight_scale/3
Wmd = weight_scale/3
Wee = (weight_scale*(E+G+M))/(3*E)
Wme = weight_scale - Wee
Wmg = (weight_scale*(2*G-E-M))/(3*G)
Wgg = weight_scale - Wmg
Case 2: E < T/3 && G < T/3 (Both are scarce)
Let R denote the more scarce class (Rare) between Guard vs Exit.
Let S denote the less scarce class.
Subcase a: R+D < S
In this subcase, we simply devote all of D bandwidth to the
scarce class.
Wgg = Wee = weight_scale
Wmg = Wme = Wmd = 0;
if E < G:
Wed = weight_scale
Wgd = 0
else:
Wed = 0
Wgd = weight_scale
Subcase b: R+D >= S
In this case, if M <= T/3, we have enough bandwidth to try to achieve
a balancing condition.
Add constraints Wgg = 1, Wmd == Wgd to maximize bandwidth in the guard
position while still allowing exits to be used as middle nodes:
Wee = (weight_scale*(E - G + M))/E
Wed = (weight_scale*(D - 2*E + 4*G - 2*M))/(3*D)
Wme = (weight_scale*(G-M))/E
Wmg = 0
Wgg = weight_scale
Wmd = (weight_scale - Wed)/2
Wgd = (weight_scale - Wed)/2
If this system ends up with any values out of range (ie negative, or
above weight_scale), use the constraints Wgg == 1 and Wee == 1, since
both those positions are scarce:
Wgg = weight_scale
Wee = weight_scale
Wed = (weight_scale*(D - 2*E + G + M))/(3*D)
Wmd = (weight_Scale*(D - 2*M + G + E))/(3*D)
Wme = 0
Wmg = 0
Wgd = weight_scale - Wed - Wmd
If M > T/3, then the Wmd weight above will become negative. Set it to 0
in this case:
Wmd = 0
Wgd = weight_scale - Wed
Case 3: One of E < T/3 or G < T/3
Let S be the scarce class (of E or G).
Subcase a: (S+D) < T/3:
if G=S:
Wgg = Wgd = weight_scale;
Wmd = Wed = Wmg = 0;
// Minor subcase, if E is more scarce than M,
// keep its bandwidth in place.
if (E < M) Wme = 0;
else Wme = (weight_scale*(E-M))/(2*E);
Wee = weight_scale-Wme;
if E=S:
Wee = Wed = weight_scale;
Wmd = Wgd = Wme = 0;
// Minor subcase, if G is more scarce than M,
// keep its bandwidth in place.
if (G < M) Wmg = 0;
else Wmg = (weight_scale*(G-M))/(2*G);
Wgg = weight_scale-Wmg;
Subcase b: (S+D) >= T/3
if G=S:
Add constraints Wgg = 1, Wmd == Wed to maximize bandwidth
in the guard position, while still allowing exits to be
used as middle nodes:
Wgg = weight_scale
Wgd = (weight_scale*(D - 2*G + E + M))/(3*D)
Wmg = 0
Wee = (weight_scale*(E+M))/(2*E)
Wme = weight_scale - Wee
Wmd = (weight_scale - Wgd)/2
Wed = (weight_scale - Wgd)/2
if E=S:
Add constraints Wee == 1, Wmd == Wgd to maximize bandwidth
in the exit position:
Wee = weight_scale;
Wed = (weight_scale*(D - 2*E + G + M))/(3*D);
Wme = 0;
Wgg = (weight_scale*(G+M))/(2*G);
Wmg = weight_scale - Wgg;
Wmd = (weight_scale - Wed)/2;
Wgd = (weight_scale - Wed)/2;
To ensure consensus, all calculations are performed using integer math
with a fixed precision determined by the bwweightscale consensus
parameter (defaults at 10000, Min: 1, Max: INT32_MAX).
For future balancing improvements, Tor clients support 11 additional weights
for directory requests and middle weighting. These weights are currently
set at weight_scale, with the exception of the following groups of
assignments:
Directory requests use middle weights:
Wbd=Wmd, Wbg=Wmg, Wbe=Wme, Wbm=Wmm
Handle bridges and strange exit policies:
Wgm=Wgg, Wem=Wee, Weg=Wed
3.5. Detached signatures
Assuming full connectivity, every authority should compute and sign the
same consensus directory in each period. Therefore, it isn't necessary to
download the consensus computed by each authority; instead, the
authorities only push/fetch each others' signatures. A "detached
signature" document contains items as follows:
"consensus-digest" SP Digest NL
[At start, at most once.]
The digest of the consensus being signed.
"valid-after" SP YYYY-MM-DD SP HH:MM:SS NL
"fresh-until" SP YYYY-MM-DD SP HH:MM:SS NL
"valid-until" SP YYYY-MM-DD SP HH:MM:SS NL
[As in the consensus]
"directory-signature"
[As in the consensus; the signature object is the same as in the
consensus document.]
4. Directory server operation
All directory authorities and directory caches ("directory servers")
implement this section, except as noted.
4.1. Accepting uploads (authorities only)
When a router posts a signed descriptor to a directory authority, the
authority first checks whether it is well-formed and correctly
self-signed. If it is, the authority next verifies that the nickname
in question is not already assigned to a router with a different
public key.
Finally, the authority MAY check that the router is not blacklisted
because of its key, IP, or another reason.
If the descriptor passes these tests, and the authority does not already
have a descriptor for a router with this public key, it accepts the
descriptor and remembers it.
If the authority _does_ have a descriptor with the same public key, the
newly uploaded descriptor is remembered if its publication time is more
recent than the most recent old descriptor for that router, and either:
- There are non-cosmetic differences between the old descriptor and the
new one.
- Enough time has passed between the descriptors' publication times.
(Currently, 12 hours.)
Differences between router descriptors are "non-cosmetic" if they would be
sufficient to force an upload as described in section 2 above.
Note that the "cosmetic difference" test only applies to uploaded
descriptors, not to descriptors that the authority downloads from other
authorities.
When a router posts a signed extra-info document to a directory authority,
the authority again checks it for well-formedness and correct signature,
and checks that its matches the extra-info-digest in some router
descriptor that it believes is currently useful. If so, it accepts it and
stores it and serves it as requested. If not, it drops it.
4.2. Voting (authorities only)
Authorities divide time into Intervals. Authority administrators SHOULD
try to all pick the same interval length, and SHOULD pick intervals that
are commonly used divisions of time (e.g., 5 minutes, 15 minutes, 30
minutes, 60 minutes, 90 minutes). Voting intervals SHOULD be chosen to
divide evenly into a 24-hour day.
Authorities SHOULD act according to interval and delays in the
latest consensus. Lacking a latest consensus, they SHOULD default to a
30-minute Interval, a 5 minute VotingDelay, and a 5 minute DistDelay.
Authorities MUST take pains to ensure that their clocks remain accurate
within a few seconds. (Running NTP is usually sufficient.)
The first voting period of each day begins at 00:00 (midnight) GMT. If
the last period of the day would be truncated by one-half or more, it is
merged with the second-to-last period.
An authority SHOULD publish its vote immediately at the start of each voting
period (minus VoteSeconds+DistSeconds). It does this by making it
available at
http://<hostname>/tor/status-vote/next/authority.z
and sending it in an HTTP POST request to each other authority at the URL
http://<hostname>/tor/post/vote
If, at the start of the voting period, minus DistSeconds, an authority
does not have a current statement from another authority, the first
authority downloads the other's statement.
Once an authority has a vote from another authority, it makes it available
at
http://<hostname>/tor/status-vote/next/<fp>.z
where <fp> is the fingerprint of the other authority's identity key.
And at
http://<hostname>/tor/status-vote/next/d/<d>.z
where <d> is the digest of the vote document.
The consensus status, along with as many signatures as the server
currently knows, should be available at
http://<hostname>/tor/status-vote/next/consensus.z
All of the detached signatures it knows for consensus status should be
available at:
http://<hostname>/tor/status-vote/next/consensus-signatures.z
Once there are enough signatures, or once the voting period starts,
these documents are available at
http://<hostname>/tor/status-vote/current/consensus.z
and
http://<hostname>/tor/status-vote/current/consensus-signatures.z
[XXX current/consensus-signatures is not currently implemented, as it
is not used in the voting protocol.]
The other vote documents are analogously made available under
http://<hostname>/tor/status-vote/current/authority.z
http://<hostname>/tor/status-vote/current/<fp>.z
http://<hostname>/tor/status-vote/current/d/<d>.z
once the consensus is complete.
Once an authority has computed and signed a consensus network status, it
should send its detached signature to each other authority in an HTTP POST
request to the URL:
http://<hostname>/tor/post/consensus-signature
[XXX Note why we support push-and-then-pull.]
[XXX possible future features include support for downloading old
consensuses.]
4.3. Downloading consensus status documents (caches only)
All directory servers (authorities and caches) try to keep a recent
network-status consensus document to serve to clients. A cache ALWAYS
downloads a network-status consensus if any of the following are true:
- The cache has no consensus document.
- The cache's consensus document is no longer valid.
Otherwise, the cache downloads a new consensus document at a randomly
chosen time in the first half-interval after its current consensus
stops being fresh. (This time is chosen at random to avoid swarming
the authorities at the start of each period. The interval size is
inferred from the difference between the valid-after time and the
fresh-until time on the consensus.)
[For example, if a cache has a consensus that became valid at 1:00,
and is fresh until 2:00, that cache will fetch a new consensus at
a random time between 2:00 and 2:30.]
4.4. Downloading and storing router descriptors (authorities and caches)
Periodically (currently, every 10 seconds), directory servers check
whether there are any specific descriptors that they do not have and that
they are not currently trying to download. Caches identify these
descriptors by hash in the recent network-status consensus documents;
authorities identify them by hash in vote (if publication date is more
recent than the descriptor we currently have).
[XXXX need a way to fetch descriptors ahead of the vote? v2 status docs can
do that for now.]
If so, the directory server launches requests to the authorities for these
descriptors, such that each authority is only asked for descriptors listed
in its most recent vote (if the requester is an authority) or in the
consensus (if the requester is a cache). If we're an authority, and more
than one authority lists the descriptor, we choose which to ask at random.
If one of these downloads fails, we do not try to download that descriptor
from the authority that failed to serve it again unless we receive a newer
network-status (consensus or vote) from that authority that lists the same
descriptor.
Directory servers must potentially cache multiple descriptors for each
router. Servers must not discard any descriptor listed by any recent
consensus. If there is enough space to store additional descriptors,
servers SHOULD try to hold those which clients are likely to download the
most. (Currently, this is judged based on the interval for which each
descriptor seemed newest.)
[XXXX define recent]
Authorities SHOULD NOT download descriptors for routers that they would
immediately reject for reasons listed in 3.1.
4.5. Downloading and storing extra-info documents
All authorities, and any cache that chooses to cache extra-info documents,
and any client that uses extra-info documents, should implement this
section.
Note that generally, clients don't need extra-info documents.
Periodically, the Tor instance checks whether it is missing any extra-info
documents: in other words, if it has any router descriptors with an
extra-info-digest field that does not match any of the extra-info
documents currently held. If so, it downloads whatever extra-info
documents are missing. Caches download from authorities; non-caches try
to download from caches. We follow the same splitting and back-off rules
as in 4.4 (if a cache) or 5.3 (if a client).
4.6. General-use HTTP URLs
"Fingerprints" in these URLs are base-16-encoded SHA1 hashes.
The most recent v3 consensus should be available at:
http://<hostname>/tor/status-vote/current/consensus.z
Starting with Tor version 0.2.1.1-alpha is also available at:
http://<hostname>/tor/status-vote/current/consensus/<F1>+<F2>+<F3>.z
Where F1, F2, etc. are authority identity fingerprints the client trusts.
Servers will only return a consensus if more than half of the requested
authorities have signed the document, otherwise a 404 error will be sent
back. The fingerprints can be shortened to a length of any multiple of
two, using only the leftmost part of the encoded fingerprint. Tor uses
3 bytes (6 hex characters) of the fingerprint.
Clients SHOULD sort the fingerprints in ascending order. Server MUST
accept any order.
Clients SHOULD use this format when requesting consensus documents from
directory authority servers and from caches running a version of Tor
that is known to support this URL format.
A concatenated set of all the current key certificates should be available
at:
http://<hostname>/tor/keys/all.z
The key certificate for this server (if it is an authority) should be
available at:
http://<hostname>/tor/keys/authority.z
The key certificate for an authority whose authority identity fingerprint
is <F> should be available at:
http://<hostname>/tor/keys/fp/<F>.z
The key certificate whose signing key fingerprint is <F> should be
available at:
http://<hostname>/tor/keys/sk/<F>.z
The key certificate whose identity key fingerprint is <F> and whose signing
key fingerprint is <S> should be available at:
http://<hostname>/tor/keys/fp-sk/<F>-<S>.z
(As usual, clients may request multiple certificates using:
http://<hostname>/tor/keys/fp-sk/<F1>-<S1>+<F2>-<S2>.z )
[The above fp-sk format was not supported before Tor 0.2.1.9-alpha.]
The most recent descriptor for a server whose identity key has a
fingerprint of <F> should be available at:
http://<hostname>/tor/server/fp/<F>.z
The most recent descriptors for servers with identity fingerprints
<F1>,<F2>,<F3> should be available at:
http://<hostname>/tor/server/fp/<F1>+<F2>+<F3>.z
(NOTE: Implementations SHOULD NOT download descriptors by identity key
fingerprint. This allows a corrupted server (in collusion with a cache) to
provide a unique descriptor to a client, and thereby partition that client
from the rest of the network.)
The server descriptor with (descriptor) digest <D> (in hex) should be
available at:
http://<hostname>/tor/server/d/<D>.z
The most recent descriptors with digests <D1>,<D2>,<D3> should be
available at:
http://<hostname>/tor/server/d/<D1>+<D2>+<D3>.z
The most recent descriptor for this server should be at:
http://<hostname>/tor/server/authority.z
[Nothing in the Tor protocol uses this resource yet, but it is useful
for debugging purposes. Also, the official Tor implementations
(starting at 0.1.1.x) use this resource to test whether a server's
own DirPort is reachable.]
A concatenated set of the most recent descriptors for all known servers
should be available at:
http://<hostname>/tor/server/all.z
Extra-info documents are available at the URLS
http://<hostname>/tor/extra/d/...
http://<hostname>/tor/extra/fp/...
http://<hostname>/tor/extra/all[.z]
http://<hostname>/tor/extra/authority[.z]
(As for /tor/server/ URLs: supports fetching extra-info
documents by their digest, by the fingerprint of their servers,
or all at once. When serving by fingerprint, we serve the
extra-info that corresponds to the descriptor we would serve by
that fingerprint. Only directory authorities of version
0.2.0.1-alpha or later are guaranteed to support the first
three classes of URLs. Caches may support them, and MUST
support them if they have advertised "caches-extra-info".)
For debugging, directories SHOULD expose non-compressed objects at URLs like
the above, but without the final ".z".
Clients MUST handle compressed concatenated information in two forms:
- A concatenated list of zlib-compressed objects.
- A zlib-compressed concatenated list of objects.
Directory servers MAY generate either format: the former requires less
CPU, but the latter requires less bandwidth.
Clients SHOULD use upper case letters (A-F) when base16-encoding
fingerprints. Servers MUST accept both upper and lower case fingerprints
in requests.
5. Client operation: downloading information
Every Tor that is not a directory server (that is, those that do
not have a DirPort set) implements this section.
5.1. Downloading network-status documents
Each client maintains a list of directory authorities. Insofar as
possible, clients SHOULD all use the same list.
Clients try to have a live consensus network-status document at all times.
A network-status document is "live" if the time in its valid-until field
has not passed.
If a client is missing a live network-status document, it tries to fetch
it from a directory cache (or from an authority if it knows no caches).
On failure, the client waits briefly, then tries that network-status
document again from another cache. The client does not build circuits
until it has a live network-status consensus document, and it has
descriptors for more than 1/4 of the routers that it believes are running.
(Note: clients can and should pick caches based on the network-status
information they have: once they have first fetched network-status info
from an authority, they should not need to go to the authority directly
again.)
To avoid swarming the caches whenever a consensus expires, the
clients download new consensuses at a randomly chosen time after the
caches are expected to have a fresh consensus, but before their
consensus will expire. (This time is chosen uniformly at random from
the interval between the time 3/4 into the first interval after the
consensus is no longer fresh, and 7/8 of the time remaining after
that before the consensus is invalid.)
[For example, if a cache has a consensus that became valid at 1:00,
and is fresh until 2:00, and expires at 4:00, that cache will fetch
a new consensus at a random time between 2:45 and 3:50, since 3/4
of the one-hour interval is 45 minutes, and 7/8 of the remaining 75
minutes is 65 minutes.]
5.2. Downloading and storing router descriptors
Clients try to have the best descriptor for each router. A descriptor is
"best" if:
* It is listed in the consensus network-status document.
Periodically (currently every 10 seconds) clients check whether there are
any "downloadable" descriptors. A descriptor is downloadable if:
- It is the "best" descriptor for some router.
- The descriptor was published at least 10 minutes in the past.
(This prevents clients from trying to fetch descriptors that the
mirrors have probably not yet retrieved and cached.)
- The client does not currently have it.
- The client is not currently trying to download it.
- The client would not discard it immediately upon receiving it.
- The client thinks it is running and valid (see 6.1 below).
If at least 16 known routers have downloadable descriptors, or if
enough time (currently 10 minutes) has passed since the last time the
client tried to download descriptors, it launches requests for all
downloadable descriptors, as described in 5.3 below.
When a descriptor download fails, the client notes it, and does not
consider the descriptor downloadable again until a certain amount of time
has passed. (Currently 0 seconds for the first failure, 60 seconds for the
second, 5 minutes for the third, 10 minutes for the fourth, and 1 day
thereafter.) Periodically (currently once an hour) clients reset the
failure count.
Clients retain the most recent descriptor they have downloaded for each
router so long as it is not too old (currently, 48 hours), OR so long as
no better descriptor has been downloaded for the same router.
[Versions of Tor before 0.1.2.3-alpha would discard descriptors simply for
being published too far in the past.] [The code seems to discard
descriptors in all cases after they're 5 days old. True? -RD]
5.3. Managing downloads
When a client has no consensus network-status document, it downloads it
from a randomly chosen authority. In all other cases, the client
downloads from caches randomly chosen from among those believed to be V2
directory servers. (This information comes from the network-status
documents; see 6 below.)
2005-09-12 08:37:31 +02:00
When downloading multiple router descriptors, the client chooses multiple
mirrors so that:
- At least 3 different mirrors are used, except when this would result
in more than one request for under 4 descriptors.
- No more than 128 descriptors are requested from a single mirror.
- Otherwise, as few mirrors as possible are used.
After choosing mirrors, the client divides the descriptors among them
randomly.
2006-01-24 01:48:42 +01:00
After receiving any response client MUST discard any network-status
documents and descriptors that it did not request.
6. Using directory information
Everyone besides directory authorities uses the approaches in this section
to decide which servers to use and what their keys are likely to be.
(Directory authorities just believe their own opinions, as in 3.1 above.)
6.1. Choosing routers for circuits.
Circuits SHOULD NOT be built until the client has enough directory
information: a live consensus network status [XXXX fallback?] and
descriptors for at least 1/4 of the servers believed to be running.
A server is "listed" if it is included by the consensus network-status
document. Clients SHOULD NOT use unlisted servers.
These flags are used as follows:
- Clients SHOULD NOT use non-'Valid' or non-'Running' routers unless
requested to do so.
- Clients SHOULD NOT use non-'Fast' routers for any purpose other than
very-low-bandwidth circuits (such as introduction circuits).
- Clients SHOULD NOT use non-'Stable' routers for circuits that are
likely to need to be open for a very long time (such as those used for
IRC or SSH connections).
- Clients SHOULD NOT choose non-'Guard' nodes when picking entry guard
nodes.
- Clients SHOULD NOT download directory information from non-'V2Dir'
caches.
See the "path-spec.txt" document for more details.
6.2. Managing naming
In order to provide human-memorable names for individual server
identities, some directory servers bind names to IDs. Clients handle
names in two ways:
When a client encounters a name it has not mapped before:
If the consensus lists any router with that name as "Named", or if
consensus-method 2 or later is in use and the consensus lists any
router with that name as having the "Unnamed" flag, then the name is
bound. (It's bound to the ID listed in the entry with the Named,
or to an unknown ID if no name is found.)
When the user refers to a bound name, the implementation SHOULD provide
only the router with ID bound to that name, and no other router, even
if the router with the right ID can't be found.
When a user tries to refer to a non-bound name, the implementation SHOULD
2007-10-25 06:17:59 +02:00
warn the user. After warning the user, the implementation MAY use any
router that advertises the name.
Not every router needs a nickname. When a router doesn't configure a
nickname, it publishes with the default nickname "Unnamed". Authorities
SHOULD NOT ever mark a router with this nickname as Named; client software
SHOULD NOT ever use a router in response to a user request for a router
called "Unnamed".
6.3. Software versions
An implementation of Tor SHOULD warn when it has fetched a consensus
network-status, and it is running a software version not listed.
6.4. Warning about a router's status.
If a router tries to publish its descriptor to a Naming authority
that has its nickname mapped to another key, the router SHOULD
warn the operator that it is either using the wrong key or is using
an already claimed nickname.
If a router has fetched a consensus document,, and the
authorities do not publish a binding for the router's nickname, the
router MAY remind the operator that the chosen nickname is not
bound to this key at the authorities, and suggest contacting the
authority operators.
...
6.5. Router protocol versions
A client should believe that a router supports a given feature if that
feature is supported by the router or protocol versions in more than half
of the live networkstatuses' "v" entries for that router. In other words,
if the "v" entries for some router are:
v Tor 0.0.8pre1 (from authority 1)
v Tor 0.1.2.11 (from authority 2)
v FutureProtocolDescription 99 (from authority 3)
then the client should believe that the router supports any feature
supported by 0.1.2.11.
This is currently equivalent to believing the median declared version for
a router in all live networkstatuses.
7. Standards compliance
All clients and servers MUST support HTTP 1.0. Clients and servers MAY
support later versions of HTTP as well.
7.1. HTTP headers
Servers MAY set the Content-Length: header. Servers SHOULD set
Content-Encoding to "deflate" or "identity".
Servers MAY include an X-Your-Address-Is: header, whose value is the
apparent IP address of the client connecting to them (as a dotted quad).
For directory connections tunneled over a BEGIN_DIR stream, servers SHOULD
report the IP from which the circuit carrying the BEGIN_DIR stream reached
them. [Servers before version 0.1.2.5-alpha reported 127.0.0.1 for all
BEGIN_DIR-tunneled connections.]
Servers SHOULD disable caching of multiple network statuses or multiple
router descriptors. Servers MAY enable caching of single descriptors,
single network statuses, the list of all router descriptors, a v1
directory, or a v1 running routers document. XXX mention times.
7.2. HTTP status codes
Tor delivers the following status codes. Some were chosen without much
thought; other code SHOULD NOT rely on specific status codes yet.
200 -- the operation completed successfully
-- the user requested statuses or serverdescs, and none of the ones we
requested were found (0.2.0.4-alpha and earlier).
304 -- the client specified an if-modified-since time, and none of the
requested resources have changed since that time.
400 -- the request is malformed, or
-- the URL is for a malformed variation of one of the URLs we support,
or
-- the client tried to post to a non-authority, or
-- the authority rejected a malformed posted document, or
404 -- the requested document was not found.
2008-05-28 06:32:59 +02:00
-- the user requested statuses or serverdescs, and none of the ones
requested were found (0.2.0.5-alpha and later).
503 -- we are declining the request in order to save bandwidth
-- user requested some items that we ordinarily generate or store,
but we do not have any available.
9. Backward compatibility and migration plans
Until Tor versions before 0.1.1.x are completely obsolete, directory
authorities should generate, and mirrors should download and cache, v1
directories and running-routers lists, and allow old clients to download
them. These documents and the rules for retrieving, serving, and caching
them are described in dir-spec-v1.txt.
Until Tor versions before 0.2.0.x are completely obsolete, directory
authorities should generate, mirrors should download and cache, v2
network-status documents, and allow old clients to download them.
Additionally, all directory servers and caches should download, store, and
serve any router descriptor that is required because of v2 network-status
documents. These documents and the rules for retrieving, serving, and
caching them are described in dir-spec-v1.txt.
A. Consensus-negotiation timeline.
Period begins: this is the Published time.
Everybody sends votes
Reconciliation: everybody tries to fetch missing votes.
consensus may exist at this point.
End of voting period:
everyone swaps signatures.
Now it's okay for caches to download
Now it's okay for clients to download.
Valid-after/valid-until switchover